base pen 3d models

... Instructions Print Put in use. See the original thing for details. I don't think this is the pen holder you want to use - it looks as though this one is setup for penup/down but the weight and balance aren't quite right.

A pen modeled just for fun.

... room" for pens vertically. Also the tolerances are a little tighter so it is harder to remove the lid, protecting the pens from spilling out when i throw them in my bag to take to work. Here are some pictures. ...https://imgur.com/a/svJf0Y6

I thought it was too tall for my desktop and shortened it and changed the base with a circle one.

I wanted to put a base on "George Hart's 3D Sculptures" hyperboloid ( http://www.thingiverse.com/image:40818 ), but I could not get it to render in OpenSCAD. So I cooked up this one. It looks a little like this one from MakeALot:...

Designed to fit the stock Frixion pen (clicker 07) which is the only example I had access to. May not fit other Frixion pens. Who knows, you tell me? It can be put in the back of the spine while closed or between two open pages when the notebook...

remix Vape pen base

I have design this base for the Wacom pen. I didn't test with other brands, but should work with similar tablet pens If you have any question just send me a message. ... Enjoy it!!

My ex-roommate had a vape pen that leaked when laid on it's side, so I created this in TinkerCAD to let it stand upright when not being used.

Base para colocar pluma de impresión 3D

DIY soldering box for 40W sold.pen with switch and 240V socket. ... ...there is no need to constantly insert the plug into the wall socket a sheet metal weight is placed on the bottom for greater stability (rectangular hole on the bottom plate)

DIY soldering box for 40W sold.pen with switch and 240V socket. ... ...there is no need to constantly insert the plug into the wall socket a sheet metal weight is placed on the bottom for greater stability (rectangular hole on the bottom plate)

Base for placing marker pens and allowing the ink to run to the tip

The composite picture show a fairly top-heavy pen and also an Apple Pencil being supported by the MagBaseV2. Print bases with higher infill to add additional weight. These bases should also work with the original model Hope you find these useful. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=56910 Instructions Using the following options: _interiorHeight = 100 _numberOfSides = 9 _part = base _lipHeight = 3.0 _resolution = 60 _minimumWallThickness = 1.0 _bayonetDepth = 0.6...

... around the shop with a fast drying bright white ink (a favorite of Adam Savage). The directions say to store it point up with the cap on. This print is a small removable "foot" that allows you to keep the pen upright when on your desk or workbench.

... 1.2mm Ballpoint pens. Mine came in a pack of 10 for about a buck, but when I went to use them the ink was all dried up rendering the pens useless. ...Instead of tossing them out I recycled them, which allowed me to make this sweet spool holder.

Instructions Print two of these parts and make sure you have 5 spare or used pens. Then snap the pens into the holes as shown. It's very easy! I used PaperMate Medium 1.2mm Ballpoint pens. Mine came in a pack of 10 for about a buck, but when I went...

Octagon base for circuit board pen holder

Pen Stand with 14mm diameter holes.

Small Pen and small objects holder to print in colors. Please ask me if you want other textures</p><p>Please ask me if you want other textures</p><p>Printed in PLA with 0.2 layer height and 0.44 width. ...don't recommend print in vase mode as the...

Greetings this time I modeled a diorama of stacked skulls and one of them pierced by a Viking sword, with the peculiarity that the sword is a pen and the stone is a drawer to store various things. I used the spare part of a feather, and from there I...

http://www.thingiverse.com/apps/customizer/run?thing_id=56910 Instructions Using the following options: _minimumWallThickness = 1.0 _numberOfSides = 7 _style = polygon _lipHeight = 3.0 _resolution = 120 _bayonetDepth = 0.6 _insideDiameter = 18.5...

Model of pens' base with 15 cases, designed to be 3d printed.

A remake of my Blastoise pen holder with a base so it's less likely to tip over when you place a pen in it

This is a Base/Stand for Vape Pen 22 by SMOK

Made a base to add to the archery pen holder made by: Anders644PI Thingy: https://www.thingiverse.com/thing:3060742 Just glue the pen holder to this base to make it a bit less likely to fall over.

Increase base thickness at ends or make glue-on covers for holding M5 nuts in place Warning: None Changes from previous versions: 0.3 added triangular support ribs to side of tower properly implemented maximum_pen_diameter made walls thicker and pen...

This is a base/stand for Vape pen 22, updated new version v4  with 15mm height v3 10mm height, 43mm diameter and inner slot for vape is 23mm diameter v4 15mm height, 43mm diameter and inner slot for vape is 23mm diameter  

It was a Bussmann High speed fuse, it is now a pen holder. The side of the fuse measure 74mm. No screw are needed for me, just punch on the right place to assemble it. ... With OpenScad, you can adapt to any need you have!