batmobile 3d model

I thought about being edgy and calling this v6.66 but I figured a name change would provide a clean slate for the community to build from.Starting with my printed Gecko 1.0, I painstakingly modeled the entire blaster in Fusion360. There were three...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 27...

... You'll hear of a good change once more after fixing and updating the walls here: with even those not fully set designs being optimized properly with a little extra bit going onto your current model too, this will look awesome when everything’s set!

This model fits seat shafts with a 16-groove, skip-tooth-top, 12mm nominal shaft: (note skipped groove, blue arrow) Probably best to print these with the spud pointed up for minimizing how much trouble the overhangs inside the hole will...

...All "mandatory" supports are already in the model. This piece on the photos was accidentally done with 0.15mm layer height and it turned out fine, although I intended to print it with 0.08mm height. Everything from 0.1mm and below should be alright.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

Sincethis design is compatible with a whole variety of lampshades, be aware that somelampshades will have to be scaled down or up to fit the base's default settings. Base- Layer height: up to 0.3mm is fine, there's little detail on the Z-axis-...

They were sold to me as "boat nails", feel free to substitute them for something else and adjust the model accordingly. For the spark gap I used a couple of bits of single stranded wire, these can be substituted for something else, multi-strand...

This model is for a “streetlight-style” wired garden/pathway light. Brighten up your garden path with lights, without spending a fortune on MoonRays or similar products where a single lamp can cost up to $20! In bulk I can make these for about $3-5 a...

https://www.youtube.com/watch?v=Nn9B46IjsVU ______________________________________________________ ENGLISH ______________________________________________________ Only tested on T12-X, but can work on equivalent models with boxes of the same...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

I can upload the design files for the other models too if there is interest. Please share your creations if you remix. : ) Update 7/16/2020 - The original inner joiner STL was undersized. I have added a new STL ("hexcell_joiner_inner_FIXED.stl")...

I found the models of the servo, sharpie, & 28BYJ-48 stepper motor on grabcad, but didn't include them in the fusion 360 assembly file here. The build log of my printer can be found here: https://openbuilds.com/builds/a-rolling-plotter.9207/ Here...

(I used bodies instead of components to avoid model breakage in case of major size change.) Required Parts list and where I got them: 1X 2032 battery holders: https://www.amazon.ca/gp/product/B08SQRSTJ4 1X rechargeable LIR2032:...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_overlap = 0 custom_back_extra_port_corner_radius = 5 printer_tolerance = 0.4 stencil_pattern_element_radius = 6...

If you want to save time while testing, you can print the included **calibration test** instead of the full model, but that is optional. Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

## Computational model The library is built around the `bladegen` function. All parameters are supplied with default values, but you may want to change these. The `bladegen` will calculate a number of points along the blade radius called nodes....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

In addition, in case you want to remix you would potentially only have to adapt the holder model.The bottom of the holder has a cavity that exactly fits a specific lightning cable found on Amazon with angled connectors to reduce the space it...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale]   One of the twin daughters of His Excellency High Bishop Madrigal, Speaker of Erdrydion. Amélie’s life has been spent entirely within the church, though in a very...

Update 01.04.2023 A friend i have made through the Neo Community have discovered that the clearance might not the good with the standart Neo, because the belt housing on the left stick out further, he have provided the file named...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Previous model description: I hooked up a 1400mah battery and drove this home from my local park around 500-600 meters with no heat issues affecting the PLA print. I have used this around the house quite a bit with the camera, and it works well. The...

It is possible that a future will make and upload a model of that piece. In the meantime, if anyone knows where to get suitable pads, please let me know. As I was saying, I started to hang them on the screw. Since the surface of the screw with the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

** FUSION360 and STEP Sources are included **** I have my printer into an enclosure and, to save the electronics from excessive heat, I've designed this model to enclose all the electronics at a singe location. These were my requirements: -...

NOTE: all models are at initial stage and not refined, nor optimized for printing, only a rough idea at the moment The unmanned colony builder/Mars MkI is a project that seeks to automate the construction of shelters and basic facilities that a...

... THANKS! Happy printing! PS.: Thanks to Rick and Morty, who posted this wonderful ASX1 model on grabcad, which I used as the basis for my renders (and my apologies for the poor quality photos - my printer stands in a pretty dark corner of the room).