battery box ebike 3d models

Dust cover for the Rockrider ST-500 MTB to keep the contact for the battery clean during transportation when the battery is disconnected.

This custom-made box is designed to hold three 4S 8000mAh lipo batteries and ten 18650 cells, demonstrating its impressive storage capacity. A total of almost 1kg of ABS plastic was used in the printing process, highlighting the complexity and...

14s 6p battery box 50% Infill or 100

Customized version of https://www.thingiverse.com/thing:1680291 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1680291

Customized version of https://www.thingiverse.com/thing:1680291 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1680291

Verticaly printed Controler Box (white box on photos) : https://www.thingiverse.com/thing:4879455 More info and photos :...

Battery box for full suspension Trek EX9 ebike to make the tight fit in the small triangle frame with the rear suspension also taking up some space. Should probably fit more full suspension bikes. Made for 13s5p 65 cell 48v battery although there is...

A battery box made for a friend for his Giant Trance MTB Dual suspension. ... It was made with holes for Velcro straps to mount to the frame

We're about to uncover a fascinating fact - just how much energy does it take to charge your ebike's battery? ...To find out, simply purchase this power/energy meter...

This fits my Norco 2009 dual suspension it may need mods for your own frame. it suits a anderson plug for charging. ...THe washers screw into the water bottle mounts.

eBike Electric battery from a ebike "universal" that I´m mounting on my brother Scott mountain bike. Soon more info on my blog http://thetrxproject.blogspot.com/. ... TheTRXproject Facebook page...

A battery holder for my ebike.

a thing to support ebike battery on round bar

inside the cap i cut about 8mm rubber that snugly fits in bottom to keep battery pack water resistant Also the frame mount parts were glued to box, maybe also fixed with screws, dont remember anymore. ... I have used this ~1500km with no problems, but...

Battery Gauge for Ebikes, I opted for an affordable Chinese Lead-Acid-Lithium-Li-ion-18650 battery gauge: https://www.ebay.co.uk/itm/Lithium-Ion-Battery-Packs-Capacity-Gauge-Meter-Indicator-Digital-Display/283041467382?var=583421126932

I'm trying to find a replacement battery holder for my eBike's HL 48-volt battery. ...The original holder was included in the Bafang ebike kit I purchased, but it has been holding up well despite being designed and printed three years ago.

Shelf to hold my battery on my ebike. uses Velcro straps to keep it in place. ...Also made a tray to keep the battery from sloshing around side to side. Category: Electronics

Shelf to hold my battery on my ebike. uses Velcro straps to keep it in place. ...Also made a tray to keep the battery from sloshing around side to side.

This Ebike Battery holder only works for batteries with the 3-Notch design.Print Settings:Nozzle: 0.4mmLayer Height: 0.2mmWalls: 3Infill Pattern: GyroidSupport: EnabledFor better results reduce the layer height to 0.12mm.

This is a replacement handle for all bosch powertube ebike batteries. Print as sturdy as possibly. ...My settings are:</p><ul><li>infill 30-50%</li><li>3 perimeters</li><li>paint-on supports for notches</li></ul><p>Happy printing</p>

I converted my bike to ebike so I needed to came up with some holder for a battery. It is Hailong battery: https://www.aliexpress.com/item/32914092155.html?spm=a2g0s.9042311.0.0.7bfa4c4dPRZptF I print this in nylon and use M5 40mm screws. PLA is...

e-bike battery case

This calls for an e-bike battery replacement.

Bottom cover for Rattan LM/LW 750 battery. ...Use to cover bontacts while charging your battery or in storage.

I Designed a cover for the battery instead of the one broken off from my bike. ... Hope it fits your battery too :)

I'm charging my Trek Rail 5 battery indoors, and wanted to have proper holder for battery. So.. Just Print it. Attach with screws tp wall, first bottom (handle end) and then use battery as measurement tool to get upper (charger end) to good...

https://www.aliexpress.com/snapshot/0.html?spm=a2g0o.9042647.6.2.74d54c4dRsM81H&orderId=3012757144333620&productId=32796315892 My 10SP5 battery is made using original Liitokala 35E 18650 lithium battery 3500mAh 3.7v 25A...

Components for the missing/broken sections of the battery sleeve. Includes faceplate, bracket, and lock assembly. ...Static study was completed on the bracket to determine width and thickness.Parts were printed using a PrusaMini and are holding up well!

... with the handle end on the bottom. Then, use the battery itself as a guide to position the top (charger end) perfectly. ...There's also an STL file available for mounting the Bosch Compact Charger on the wall, and it requires no supports whatsoever.

My original battery cover was so frayed, that it was nearly impossible to put it back on.So I printed a replacement in PLA, for my surprise it fitted perfectly. ...It's easy to remove and wont get lost while riding.