bd x 3d models
326687 3d models found related to bd x.
thingiverse
These are my X and Y axis endstops for Tony_921's gantry replacement. As you can see in the pictures both of these endstops zero my printer perfectly. The Y endstop needs two holes for short M3 screws drilled into the front of the printer as shown...
thingiverse
... allows belt tension adjustment by pinching the belt between the teeth on the back of the carriage. It also allows the left and right sides to be be different heights to accommodate the height differences between the x pulley and right side bearing.
thingiverse
... shroud mates with the extruder housing. ... Routes airflow around the extruder in as narrow a space as possible (for extra X travel) and focuses it on the downtube to support better high-speed printing. ... This updated design is still being tested.
thingiverse
These parts will allow you to extend the X and Y of your bed. You will loose some Z. The reason for the loss is to get the bed above the bearings and the printer base. Instructions Just print the...
thingiverse
This the the QU-BD RPM's X-Y gantry structure assembly drawing. ... The model is upside down as shown on thingiverse...
thingiverse
This X-carriage is loosely based on Tony_921 x-carriage with a metal holder. I have made three major modifications. I printed this at 0.2mm height with ABS and 20% infill. Shifted the bearing holders slightly to the right. This adds about 5-10mm of...
thingiverse
This is a adapter plate to mount the QU-BD extruder to the X carriage on the Prusa i3 (Einstein Variant rework). I attached the X carriage file by J. Prusa so you dont have to look for it. Use 3mm socket cap screws to attach to the X carriage...
thingiverse
Replaces X-axis hotend carrier and mount. Default one is too heavy and IMHO not very well design. This carries is a mash-up form thing 218670 and thing 224301, but with bowden setup. I recommend using Airtripper extruder for simplicity, but feel...
thingiverse
To use this with the stock z-carriage on the idler side you will need two low profile M5 screws and two M5 locknuts for the pulley axles, and you will need one hex head M5 x 30mm screw, 1 or 2 M5 washers, a standard M5 hex nut and some light duty...
thingiverse
I designed this part to fix the belt of the x-axis. ...I printed this with belt fixed with double faced tape and then glued this part.
thingiverse
This is an X Carriage for a single QU-BD extruder. I have included the SCAD file though it is really a mess. Instructions This thing prints in two parts. Assembly should be obvious. The nut traps...
thingiverse
Extra parts to purchase: (4) M3 x 8mm screws (2) M3 x 12mm Screws (2) M3 x 35mm Socket Head Screws (required only for Single Body Extruder) (8) M3 Hex Nuts (1) M4 x 20mm Screw (1) M4 Hex Nut (1) 5/16-18 x 1" Button Head Screw (1) 5/16-18 Lock Nut...
thingiverse
I only had M3x20 around so I modded the original design from bdwalker1 to work with the shorter screws. This approach only uses three screws to mount the motor. Its sturdy enough and was an easy way to modify. Hope you like it. ...:)
thingiverse
The qu-bd model came from here: http://www.thingiverse.com/thing:51916 Gonna try to sneak a test print at work tomorrow and check the fit. I need to come up with a way to hold the extruders down when closed. I added the sketchup model, feel free to...
thingiverse
Instructions Reworked the X_Switch_and_ZAdjuster-_for_MacAttakextruder-_v1.scad file to create a new mount to move the endstop -Y (to clear the X-drive belt) and +X (to clear the stepper motor and end of travel). Note that the Sainsmart endstops...
thingiverse
Had to make a z-Enstop Mount for this setup: https://www.thingiverse.com/thing:1580899 & https://www.thingiverse.com/thing:2628544
thingiverse
more up to date version http://www.thingiverse.com/thing:615689
cults3d
more up to date version http://www.thingiverse.com/thing:615689
thingiverse
Same as the single extruder version, but properly spaced for dual MK7s and any clones such as QU-BDs. The cheap way to add dual extruders. BTW, the key here is this mount exactly follows MakerBot's dual extruder mounting spacing for both T-O-M...
thingiverse
Customized version of https://www.thingiverse.com/thing:415487 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=415487
thingiverse
Customized version of https://www.thingiverse.com/thing:3530989 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3530989
thingiverse
Customized version of https://www.thingiverse.com/thing:3530989 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3530989
thingiverse
Customized version of https://www.thingiverse.com/thing:3530989 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3530989