bed frame corner protectors 3d models

A corner protector for a bed frame made of 185x30mm (cross section) wooden planks. It neatly covers the mitre joint of the two planks. Just tack or glue the protector to one plank and slide in the other. Connect the planks with a bracket. It is...

These corner protectors with their filleted edges cover the sharp corners of the bed frame. Blu-tac is used to hold the corner cover in position. ...Print Settings Printer: Da Vinci 1.0 ...

Hypercube Bed Corner Frame to improve Rigidity. ... Needs : - 1 M5x10mm - 1 M6x25mm

Lost the end caps for your metal frame? Those edges can be sharp! ... This little cap can help.

We turn our bed sideways for more room, leaving the metal frame exposed. My wife keeps hitting her shin on the bed's metal frame. So I decided to make a cap to reduce the impact. I would like to make it clip better and add a gap for a rubber padding...

Box corner joints/protectors

This is just a silly Seckit branded corner piece to pretty it up ;)

Cabinet corner protectors for guitar amplifier heads or speaker cabinets.

corner protectors for vinyls, for single vinyl packaging (5mm) and for double vinyl packaging (8mm)

Safety Corner Protectors Guards I have always been a fan of help, and quick fixes, especially when possible. Suggestions are always welcome. ...Stay healthy - and enjoy!

... of 38mm seems to be pretty common. It fits both on the dining table and on the kitchen countertop. Either glue this protector to your table corner, or press a rubber shim in. ...I did the last one, in order to remove it without any damage.

The corners of my 3D printer enclosure were home made and were pretty sharp. ...I then took the measurements and created a cover for it such that the acrylic panel stays in place and the sharp corners are not exposed.

this is little pastic corner that will slip stright onto the acer spin 5 to protect from damage.

Book corners based on reversed fleur de lys symbol Both a version with fake rivet studs to be glued on the book and one with holes for real rivets available. ...

Book corners based on reversed fleur de lys symbolBoth a version with fake rivet studs to be glued on the book and one with holes for real rivets available. remixed from https://www.thingiverse.com/thing:652068  Category: Decor

Just a corner protector

My Thor 210 has nubs on the end of each arm to protect the motor in a crash, whilst this works great it does mean the end carbon gets damaged, I designed and created some bumpers to take the impact without adding the weight of an entire motor...

Corner protectors for Worx Landroid M robotic mowers. Just print and stick some double sided tape on the inside, and then carefully slide them onto the chassis, making sure the tape doesn't stick until fully seated. Using glue is of course also an...

SummaryCorner protectors for Worx Landroid M robotic mowers. Just print and stick some double sided tape on the inside, and then carefully slide them onto the chassis, making sure the tape doesn't stick until fully seated. ...Using glue is of course...

... from knocks. These work great with #6 x 1/2" flat-head screws. Longer than 3/4" screw tips may interfere with one another. The x4 .stl file is four identical copies of the single corner, for easier printing of full sets. ...No supports needed.

I created this to protect the corners on my Jawbone Big Jambox. As a side result, the elevated speakers seems to provide a little more bass possibly due to bouncing off of the surface?? There are two versions included in this Thing. The first...

Bed corner

Stackable corner frame.

Corner joint for 3/4" metal tubing from hardware store (towel rod) that was used to make a frame for honeycomb bed retrofit of Chinese K40 laser cutter. Could be used to build anything... ...shelf, box,...

Corner joint for 15mm metal tubing from hardware store (towel rod) that was used to make a frame for honeycomb bed retrofit of Chinese K40 laser cutter. Could be used to build anything... shelf, box,... Edit: I mislabeled the size (15mm was 3/4").

Corner joint for 3/4" metal tubing from hardware store (towel rod) that was used to make a frame for honeycomb bed retrofit of Chinese K40 laser cutter. Could be used to build anything... shelf, box,... ... Printed in ABS with no supports and 20%...

Since i had that experience, i designed a simple corner bumper for this bed. It's the best if you print it from a flexible material, like TPU, but in my experience simple PLA works also. Its hard, but you don't get that sharp corner at least. ...

CORNER FRAME Created for a wooden PC project it would have been better if they were printed in brown wood effect. ... No supports needed

I printed 4 of these corners using Inkscape and openSCAD (Source files provided) to hide the nasty woodwork on a white board frame Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No Resolution: 0.1 Infill: no

Used to mount the glass print bed to the sub bed.