beebrain v2 camera mount 3d models

I remixed ironhalo's mount from thingiverse because it doesn't fit if you build the official enclosure. With this remix you can fit the raspberry pi camera in your enclosure. ...The mount is designed for the left printer side. Print...

This is a remix to work with the camera mount thing:2812913 It can be mounted in different positions. Added holes with recesses for m5 hex bolts. ... By being attached to the bed support plate it moves with it, so time lapses stay in focus and appear to...

Mount your PSVR camera to any standard tripod using a 1/4" nut secured with super glue at the bottom. ...Attach the mount to the tripod with ease and secure it in place using velcro on the back, allowing for seamless placement on walls without drilling...

Mounts a Yi Dome Camera to an Ender 3 Printer. Compatibility assured for other printers with similar rail systems. Successfully tested with Dome, potential compatibility with other Yi products pending verification. ... Two versions of mounting hardware...

The gun rest attaches securely to most camera mounts via a 1/4" - 20 threaded bolt. A hole is drilled, then tapped for a 1/4" - 20 thread, creating a snug fit that prevents slippage. ...If you lack a tap, you can heat a 1/4" - 20 bolt until it's pliable...

... were in TPU but currently flying with PLA version for reduced potential of vibrations. Designed to mount with original Aura front bumper and beeper mount. ... Adds a slick look to the front end, and much better camera protection and adjustability.

A custom FPV camera angle mount designed specifically for a quadcopter is now available for users. The mounting system has been engineered to hold cameras with maximum widths of 30 mm securely in place. The FPV camera can be positioned at precise...

I specifically designed this mount with renters in mind, knowing how strict some landlords can be about putting holes in the walls for hanging pictures or security cameras. The mount simply slips onto the top shelf of any tall Walmart shelf, as you...

A custom-made clamp style mount is now included, allowing you to pivot your camera within its larger holes and lock it down firmly using a sturdy M3 bolt located directly behind the lens. ...This reinforced setup greatly improves stability by minimizing...

Designed for RotorX RX122 Atom, three camera mounts are available at angles of 15, 20, and 25 degrees. These camera mounts work well with Rev6 Naze and Genix pdb boards which make the usb connector exit from the front. As a result, right-angle USB...

With the camera mounted to the base and octolapse on a raspberry pi, I get lovely timelapses with no extra mass being moved about by the printer. ... Visit our blog to see this and other projects we have completed https://realbaddad.com 3D Printed...

The camera mount upgrades the standard QX 90 model, featuring guides that securely keep the camera in place on its base while shielding the antenna with protective support. Weighing less than a single gram, this miniature design barely registers on...

Therefore, I customized the mount in conjunction with rockpaperlizardspock's camera mount and some space to work with the 40mm ribbon cable, and added a thumbnut as a final touch since I only had a 20mm and 65mm M5 screw available to hold everything...

This mirror installation is intended to assist with parking and does not provide a good angle (camera is mounted too low) for full time use while driving. This mount is designed to be used with two brass heat set inserts and four M3 screws. ... The...

They come with a mount that screws onto something, while on the other end is a fitting where a tripod screw mount can be attached. An M3 bolt and wing nut hold the mount firmly in place on the pipe. I purchased one of these adapters from eBay at...

This mount is engineered to pair perfectly with the ION Camera clip, specifically designed to accommodate the ION Camera's standard mounting mechanism. The entire structure comprises two halves: an upper portion and a lower section secured together...

*update - added 30 degree AIO version by request Versatile camera mount for 20x20 stack microquads: -Offers great protection for lens and electronics -Fits both AIO (TX03 / FX798T) and separate camera and VTX (e.g. VTX03) or split AIO -Double tie...

I wanted to mount my Raspberry Pi Camera close to the bed but not on the gantry beam in the rear.The Camera just fits in this position without being hit by the toolhead (tested with Stealthburner) and without interfering with the front idler.When...

I've found these velcro mounts for the GoPro Hero video camera that can be easily attached to RC plane fuselages and wings. I've since used them to attach the camera to my leg and helmet, and they work exceptionally well. I used these same mounts to...

... any suggestions or ideas for improvement, feel free to share them here. I also created a slightly larger version with an even better design. To build this camera mount, you'll need: 2 M5 nuts 1 M5 cap nut 2 Allen screws (M5 x approximately 15mm)

Corner mount for security cameras or baby monitors that allows for easy installation at an optimal viewing angle of 22.5 degrees downward. This design is ideal for cameras that struggle to tilt down sufficiently or lack sufficient flexibility. This...

Designed specifically for use with an Open Eye camera, this mount allows you to easily mark the spots where you'll drill through a 3" x 3" square base made of 1/4" thick material or its equivalent in metric measurements (76mm x 76mm and 6mm). To...

... capturing the action without worrying about damaging your equipment. Perfect for outdoor enthusiasts, action sports athletes, and content creators alike, this camera mount is an essential tool for anyone looking to elevate their visual storytelling.

...This comprehensive guide will walk you through each step of the process, ensuring a seamless integration of the camera mount. The Mk 20 EO turret is specifically designed for P8 Poseidon conversions, offering unparalleled flexibility and precision.

Fits are designed into the structure to support the camera, which is sized precisely for an 10x10x10mm FPV unit. If you're looking for mounting options for your small drones or quads, this custom design could provide a viable solution. ...Instructions:...

To assemble this mount, print both the mount and cover separately, place the camera inside the mount, and then glue the cover at the rear to keep everything secure. ...For more details on installing the video transmitter, check out my other project - an...

Artillery Genius Camera Mount for Standard Cameras with a 1/4-20 Threaded Hole. Attach the mount to the stepper motor on the left side, securing it with 3 x 40 mm screws after removing the existing Philips head screws from the bottom of the motor.

The C920 camera mount was just something I carved up from another mount, but I wanted something more universal so I slotted a 10mm hole in the center of the wishbone for anyone to use any camera mount they wanted, as long as it can support a 9.5mm...

My base mount is designed to provide ample space for securing the gimbal as needed, while also allowing users to attach cameras to the Tilt Mount plate in their preferred configuration. The mounts are versatile and can be used with servo horns or...

This is a custom-made BRIO camera mount specifically designed for DIN mounts, with no modifications made to the BRIO itself. There are several base options available, catering to different preferences. If you want your camera positioned straight...