beebrain v2 camera mount 3d models

Support for the small tx06 camera to be applied to Syma type drones in front position.The support requires the use of two small self-tapping screws.For more detail visit: http://www.tutorial360.it/default/tutorial.php?id=380

I've been searching everywhere for a straightforward 14x14 camera holder, but couldn't find one that suited my needs, so I rapidly drew one up and shared it here. ...I'm excited to hear your thoughts on this design!

This is a dedicated accessory for the Excelvan family action camera. Tested specifically with two models: the TC-J6 and the TC-Q5. ...It's designed to connect seamlessly with the support system offered by Excelvan.

I strategically placed a vacant space at the forefront to prevent obstructing the FPV camera underneath. ... This innovative project was designed using Tinkercad, and you can easily edit it online by visiting https://www.tinkercad.com/things/6KzEDrE1A5u

https://www.thingiverse.com/thing:2758555 this is a remix to build a cheap homemade 4k 3d Camera for 3d movies useful for VR movies .;-) i use 2 Soocoo F91R Action Cams.

I required a compact, straightforward wall bracket for my D-Link camera and discovered the thingiverse website, specifically the model 2440785, which I adapted to suit my needs, then printed it with great results.

https://www.thingiverse.com/thing:3497182 Changes in the Model: - Securely attach the camera for printing directly onto the side. ...- Efficiently fasten the model to the bed using a secure bolt.

I based my design of these two other holders: - https://www.thingiverse.com/thing:3891092 - https://www.thingiverse.com/thing:4321156 But needed to create my own that shifted the camera a bit more to the top of the lid since otherwise the...

I reinforced the casing by drilling two precise holes on each side, then secured a makeshift bridge using a paper clip to safeguard the sensitive camera antenna from potential damage.

Wanted to attach two cameras to one tripod, so created an adapter for it. The center hole is threaded with 1/4-20 thread, allowing direct screwing into your tripod quick release plate. The outer holes are standard 1/4 inch holes, requiring you to...

Because the camera won't sit all the way back against the frame crossbar (it is too wide to fit in the space), there's a little stub in the 3D print designed to take up the gap to keep the camera pointed roughly straight. To install: pop the camera...

... tutorial on Instructables! https://www.instructables.com/id/DSLR-Camera-Lamp/ The recipe is the following: 2 X M5 nuts some M5 threaded rod this model (I used PETG) and something on the other end + what that stuff needs Category: Machine Tools

... left over for additional components such as a tripod adapter or extension cable if needed. To secure the camera in place, carefully drilled holes must be made for attaching it and its integrated swivel arm to ensure precise and flexible positioning.

... environment (night vision). It also has Wide Dynamic Range WDR which improves dramatically the video quality of OpenHD. There are numerous settings exclusively for this camera which I’m planning to test them all. ... https://youtu.be/_KZm4thByM0

I enhanced this by adding a hole in the center to accommodate a small backup camera, which has a slimmer rim around its edge to match the latches on the device. Improved version: http://www.thingiverse.com/thing:767820 Instructions...

It comes in two versions, one featuring a smaller base ideal for securing the camera using elastic bands on either side, while the other has a larger base suitable for use with double-sided tape or a single piece of elastic. ...Simply print out both...

I'd do any modification needed. NOTE 2: Put the anchor point in the opposite side of the ribbon cable slot orthe holes will not align! A no fuss alternative camera holder for pbroeder's arm mount. Use it together with TeachingTech's flexible webcam...

I paired the TX01 mount from Electronicx, a thing ID of 1904465, with the clip-style mount from aliimam, identified as thing 1906041. ...The resulting angle measures precisely 22.5 degrees.

I required a means of crafting a more versatile mounting system. ...Thus, I elected to design a compact tripod adapter for the Wall Mount Round Base Flexible Bracket Stand.

This is a camera holder that attaches directly to 2020 aluminum without needing any additional parts except for two $2.30 webcams and some zip ties. It was designed specifically to hold the cheapest webcam I could find on eBay. I've been using...

They increased the mount settings to 35mm to be compatible with the Eachine Wizard X220 drone body.

Lightweight and compact replacement for bulky stock mount. ...Not as versatile as the original one but does its job well.

Remixed to be more stable and reduced to 2 mount points due to be compatible with modular articulating arm.

This is a small spacer made for a Harbor Freight magnetic base GoPro mount I came up with.

I modeled this mount to use in my Creality enclosure, but it serves any other purpose. ... Ø 16mm

This is a remix design of a file from thingiverse. ...It is designed to work with gopro style mounting brackets.

Just the basic envelope of the thing, don't need to get overly anal retentive and make it look like the exact thing with all the bells buttons and needless features.This will be made from HDPE because it only needs to hold the camera fixed in...

One potential area of improvement would be to adjust the camera's angle of view to maximize visibility on the ground while minimizing sky exposure. To achieve this, I could tilt the camera downward slightly, allowing me to capture more detail in the...

This adapter for the Craftbot+ utilizes a raspberry pi camera paired with a fish eye lens readily available on eBay. It attaches seamlessly to the existing M3 screw on the right-hand side window, eliminating the need for any modifications to the...

I made this camera holder because i dont have the "slide in" part, only the Camera Case itself, and it was more easy to just create on for myself :) And share it ofc. ... I sized it so Xiaomi 4K+ case is close to the weapon as possible, but the case...