behringer model d stand
2018592 3d models found related to behringer model d stand.thingiverse
Behringer_Model D stand, Simpel but effective.....change if you want, but it works for me. ... I hope you can use it :-) Have fun, and make some music.....
thingiverse
A set of legs for the Behringer Model D synth, inspired by this design: https://www.thingiverse.com/thing:5340392 I printed in PLA+ at 40% infill and found it printed very well.
thingiverse
A basic stand for the Model D which allows cables coming out the back of a Keystep to pass underneath. The stand also angles the unit forward 30°. Assembles using a length of 20mm aluminium box section (I didn't have any threaded bolt like the...
thingiverse
This stand can be used to hold Eurorack style synthesizers like the Behringer Model D and Behringer Neutron.
cults3d
For basically any of the mono synths from Behringer like Neutron, Model-D, CAT, Wasp etc. Lots of cutouts for cables on the back. Prints easy and uses few material as possible. Standing solid. ... Support available, just contact me.
prusaprinters
This extension allows you to fit Behringer Model D into the same rack/stand with Neutron, Pro-1 or other synths of the same size and case style. It's construction allows to install up to 8hp Eurorack modules. Mirror it in your slicer if you wish to...
grabcad
I modelled my Behringer Model D which is a clone of the legendary Moog Minimoog (Model D) analogue synthesizer. The Minimoog has been produced during the seventies, and is still a very expensive piece of gear. Behringer made a good job in creating...
thingiverse
I made a side panel for my Behringer for a direct replacement so you can change colors or make Star Wars versions like I did.
thingiverse
The DCAPS are 3D printed PLA stands for the Behringer Neutron and can be used: - As standalone tabletop stand (perfect for the Model D in combination with Arturia Keystep Midi Keyboard) - As extension of an Eurorack - As extension of the DCASE
prusaprinters
The DCAPS are 3D printed PLA stands for the Behringer Neutron and can be used: As standalone tabletop stand (perfect for the Model D in combination with Arturia Keystep Midi Keyboard) As extension of an Eurorack As extension of the DCASEPrint...
cgtrader
*The Legend * The legendary Moog Model D in its modern version produced by Behringer: The Poly D
thingiverse
Rack ears (bracket) for mounting the Behringer Model D ("Boog") in a standard 19" rack. You can use the existing fasteners to mount the rack ears to the unit. ... The mounting holes are oval to accommodate slightly different rack widths.
thingiverse
DESCRIPTION These risers are designed to lift and rotate your Behringer MODEL D for ergonomic use on a desktop or other flat work surface. Each riser can be mounted with the two forward facing side panel screws currently installed on your MODEL D -...
thingiverse
... not be available until 2020, I created them myself. This is for following models tested: Model D, but should also work with WASP deluxe and CAT. All have the same width. Rack ears for other models from Moog and Behringer will be added soon. ...
thingiverse
To mount the DCAPS on the original Behringer Model-D case, remove the 4 screws on each side of the case and remove the metal and wooden panels. Re-use the 4 screws to screw the DCAPS onto the metal case. At the front of the DCAPS there are holes...
prusaprinters
DCAPS are designed for the Behringer Model-D case and can be used either as table top (perfect with Arturia Keystep) or as an extension of an Eurorack Modular System. To mount the DCAPS on the original Behringer Model-D case, remove the 4 screws on...
cults3d
Stand for Behringer C-1U hub, with groove to pass the USB type B cable.
thingiverse
Simple stand for Behringer Xenyx 502 to prop it up Designed in Fusion 360
thingiverse
Behringer audio mixer stand so it sits on the desk at an angle - easier viewing when sat down
thingiverse
This is a simple [BEHRINGER UM2](https://takulog.info/BEHRINGER-UM2) stand which is one of simple audio interface. I made this PVB filament for the gross of this picture, but it can be made by PLA, and so on. ... ---- [ベリンガー...
thingiverse
Set of synthesizer module stands for the Behringer Crave module. ...Simply replace the existing end caps (2 screws on each side) with the newly printed stands
thingiverse
This is a vertical stand for the Behringer UMC404HD. ...It was taking too much desk space so I decided to do put the 3d printer to work.
thingiverse
Simple stand for the small Behringer 502 mixer. You'll need 4 screws M4 x 15 to mount the frames. ... The frames have a close fitting, this is part of the design :)
thingiverse
My buddy needed a stand for his Behringer XENYX 1202.Mixer, so I created one. Inside measurement for this stand is just under 9 1/2" wide. Noticed the pictures messed up; View original and see the true view of it. ...
thingiverse
I needed to see better on these little micro devices from behringer so I have designed a stand for them which just slides on and hold itself to it. It fits every Micro device from the Behringer line up. It is a 30degree stand so the viewing angle is...
thingiverse
This is a table top stand for the behringer mixer series the space between the "hooks" is 26mm so if your mixer is the same or thinner, it will fit. the connections are friction fit, so you have to use a tool to press them together. ... see picture
thingiverse
A simple stand for the Behringer Crave that positions the synth in an 45° angle. Simply print 1 or 2 of them and put them underneath the synth. They are snug fit so I did not constructed a traverser to keep them in a fixed position relativ to each...
thingiverse
I created this so my Behringer MX602A stand on top of my modular synth case and have good access to the controls. It uses the same screws that hold on the original side plates. Printed fine for me without supports. ... Made in Fusion 360.
cults3d
This is a simple BEHRINGER UM2 stand which is one of simple audio interface. I made this PVB filament for the gross of this picture, but it can be made by PLA, and so on. ... ベリンガー UM2 向けのスタンドを製作してみました。ポイントは、XLRケーブルを後ろに回せる真ん中の穴で、デスクが散らかりにくくなっています。 ...
thingiverse
... a synth underneath/in front of my k-2. I'm assuming this will work with most behringer synths as they all seem to have the same side panels? ...Getting a wasp soon, will check and update, or if anyone knows for sure feel free to comment :) thanks