bell super dh camera mount 3d models
470987 3d models found related to bell super dh camera mount.thingiverse
Chin mount for Bell super dh helmet, it click on helmet and it is ready to go...
thingiverse
Chin Mount for gopro with a zip tie of 2,5mm Very simple and clean for Bell Helmet DH
thingiverse
... on this platform and share my designs here. Please respect my decision. **Mirrors:** - https://cults3d.com/en/3d-model/various/bell-super-dh-minimalistic-gopro-chinbar-mount - https://bit.ly/3ntGkGW **Edit:** They do not even support .3mf yet?!
cults3d
This simple GoPro mount is meant to be clipped instead of zip-tied, to easily break away in case of an accident. I can be zip-tied if you want to, as seen in the images, but it perfectly stays in place, without fixation. I used a M5 square nut,...
thingiverse
I changed the Nut Holder to fit a Standard M5 Nut. Also increased multiple clearances, since printing it with 0.2mm was way to tight. ... Make sure to print the side with the Nut Holder up - use some Superglue to secure the Nut.
thingiverse
I lost screws of my bell helmet so I need to recreate it. You cal print the merged screw or print (in two color) its components. ... The ring is in common and then you can choice to print the bolt with B logo or with jolly joker.
thingiverse
I needed a Chin Mount for my Passenger Helmet - Bell Qualifier - but didn't want to waste $35 on one from that one site that sells chin mounts. (In all their product images, they look 3D Printed anyways) plus the one available also required the extra...
thingiverse
This is a print in place model to mount a GoPro to the chin piece of a Bell Super 3R mountain bike helmet. You don't need any zip ties or modification etc.. ...Enabling tree support (assuming Cura) probably leaves the least cleanup post print.
thingiverse
Adapter to mount a GoPro to the chin bar of a Bell Super Air R helmet. Requires a standard bolt & nut out of the usual GoPro mounts, and is attached with 1-5 zipties (depending on how secure you want it). Printing with 100% infill is recommended,...
cults3d
Adapter to mount a GoPro to the chin bar of a Bell Super Air R helmet. Requires a standard bolt & nut out of the usual GoPro mounts, and is attached with 1-5 zipties (depending on how secure you want it). Printing with 100% infill is recommended,...
thingiverse
Is a clip on gopro mount for a Bell 3r Convertible downhill bike helmet. It is clip on, and has a slot for Velcro Three versions - is a clip on design but different helmets seem to have different jaws. The v11 is for an XL - the V12 is for an L. ...
thingiverse
This camera mount will allow you to easily mount most CCD and CMOS board cameras. A nice affordable way to get your Super Bee FPV ready. ...Print Settings Printer Brand: RepRap ...
thingiverse
This is my first share of stl, just want to share with others my experience about it https://www.youtube.com/watch?v=nUeB1tJA91Y I was looking for a eye wear mount for my Bell and Howell tac action cam and I can't find any that suites my need so i...
thingiverse
Sony HDR AS20 adapter for Bell Super 3R GoPro mount Hexagonal head screw M5x40 Bolt M5
thingiverse
This thing will allow you to mount a Rockbros V9C-800 LED light to a Bell super helmet mount (using the helmet's GoPro adapter).
thingiverse
simple camera mount for FPVWRA spec wing / super spec wing
thingiverse
Redesign of the FT Super Bee camera mount. I added a 4mm deep 6mm wide recess so that a PZ0420 camera fits (the threaded ring that fixes the lens stuck at the hole for the lens was to wide for the original design) also I added more narrow screw...
thingiverse
DJI O3 camera mount for Super G and Super G+ Printed in PETG or other hard plastic such as nylon or ABS, Replaces the front 2 standoffs **Part will need to be mirrored in your slicer to have both left and right versions** Edit #1: New files added...
thingiverse
Check the Version 2 for updates.) Here are some fixed camera mounts for the Catalyst Machineworks Super Light 3" in 20 deg, 30 deg, and 45 deg variants. The STL and Solidworks SLDPRT files are included with the download. Feel free to modify them...
thingiverse
Remix of Super Compact Pan Tilt Camera Mount by AtomKemp. anfPanTiltBase 1. Combined {vertMount, panTilt, bracket} 2. Removed curvature in vertMount to better fit sg90 anfPanTiltPlatform 1. Removed two of the sg90 nubs 2. Increased size...
thingiverse
I wanted to create a simple camera mount that was lightweight and printed quickly and was forward enough to not show the props on my tiny whoop. This prints flat, use a lighter/torch or heat gun to warm up and shape the struts. Takes a little trial...
cults3d
In my setup I have: 1 x-axis mount (grey) 2 arm (light blue) 4 pivot (green) 4 washer/nut (red) 1 Camera holder (dark blue) 7 5mm screws Added an extra hole to zip tie different types of camera if you are using a different camera than this was...
thingiverse
In my setup I have: 1 x-axis mount (grey) 2 arm (light blue) 4 pivot (green) 4 washer/nut (red) 1 Camera holder (dark blue) 7 5mm screws Added an extra hole to zip tie different types of camera if you are using a different camera than this was...
thingiverse
a remix from westers47's great part but this one accepts a HS1177 camera to put FPV in the nose of your FT Super Bee. Two parts now, one to fit a standard lens, and one with a larger opening to fit a larger lens (like is on the runcam owl plus, or...
thingiverse
... Instructions Print out each part and glue them together (this might require a bit of trimming as the tolerances are tight.) The camera mount is supported at one end with a 2-56 x 1/4" machine screw and the other side is supported by the servo horn.
thingiverse
Print in TPU, with supports. ...Mirror for other side. On the Super G+ it Keeps FOV 95% clear of props and frame, with little bits showing in the corners in wide mode 4:3.
thingiverse
... This is designed with a 10 degree up-center angle so if you mount it to the side of your door it will point more toward the up-center of your door. ...You can mirror it along the axis to make the angle point the camera to the opposite direction.
thingiverse
Having lost a screw from the visor on my Bell Super helmet, I decided to replicate one including several options : A whole screw modeled in plastic, A "cap" for an M5 round head screw, and another version that allows am M5 screw to be bolted through....
thingiverse
Camera mount for the SuperG using the DJI O3 Air Unit. It will give you unobstructed view corner to corner. ... Included a thing that I used to mount the antenna in the back as well.