benjamin franklin 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Anyways, this is getting out of hand so here's the important stuff: Many models to choose from! 18mm sensor 12mm sensor 8mm sensor Then choose you cap: 2 stock fans with chain mount 2 stock fans no chain mount No fans no chain mount No...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Note: don't order a GearVR with a white body - it is a 2015 model with smaller lenses that don't fit. UPDATES V3.3 (slight comfort improvements over v3.2). [print 1 for each eye] Added a version for the prescription inserts from VR Lens Lab (also...

Yes, there's an actual tank model underneath all the nonsense; it's just badly covered over since I built a spacefuture tank around it. I used a different source for my sponson lascannon; the sponson mount is from Seb's Sicaran proxy, so any of its...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

It's corrected in the download-model.I know, this LCD knob is completely over-engineered and basically totally nonsense. But it was fun to design it and bring it to work for the LCD knobs contest.Triggered by verny's Cardan Joint Knob I thought I...

The Doors Pack includes 47 models (each in .stl and .obj format, making for 94 files) and adds a treasure well of different doors to make your dungeon unique. It is also the first expansion pack I got ready to publish. Some of the doors come in...

The initial idea was to couple the two 4020s to the original TTBluer case, however it has lower flaps that made the process difficult, as I wanted to preserve the original part without cutting flaps, I decided to model a new case. I have results...

* Test your work again * replace the toothpick with the mounting pins * improve the models and share your changes with the rest of us! The difference between this and the original is that I have add a version of the body which has an opening...

On the single phase motor models there's contactors and timers in there for the auto tapping function... if fitted. I wired the 12 volt psu's mains connection to the main switch of the mill, this is after the main fuse so it's protected by that,...

As I'm new to parametric modeling, this solution was done without adhering to full parametric techniques. I'm still learning. The KeyAll HV has two mounting holes, which left 2 open feet for other uses. One foot was left unused, and the other to...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl, and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Got home from work, so now it's time to work: My initial model idea looks nothing like what I later end up with. Its bulky and more suited for clipping onto a credit card. The idea was there but not the form. I just kinda thought of the idea and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_overlap = 0 custom_back_extra_port_corner_radius = 5 printer_tolerance = 0.4 stencil_pattern_element_radius = 6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

The model can accommodate slightly larger and smaller sizes as is. To fit your doorknob you may either scale the STL file before printing (measure your doorknob diameter D and scale by D/54), or adjust the parameters in OpenSCAD, render (F6), save...

also know with ESC if you turn power off with pot turned to high you have to turn the pot down to be able to start motor again (must be a ESC safety thing) Machine drilling a board the failed to drill completely through on the CNC PCB Mill ( My fault...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: Divine Awakening]   The third child of Tharador, Renmaeth is the custodian of his body, the continent of Tharador. In the Age of Creation she shaped the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...