best upgrades for anet a8 3d models

I designed a Full Graphics LCD case that mounts directly to the Anet A8's acrylic frame because there weren't any available. My design was based on wersy's case, which I referenced heavily. User vtoryh took wersy's case and modified it to include a...

Print instructionsCategory: 3D Printer Parts Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: .2 Infill: 10 Notes: Print two end pieces and as many guide pieces as you need to fill the edge. On my printer, 2 end...

Print instructionsCategory: 3D Printer Parts Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: .2 Infill: 10 Notes: Print two end pieces and as many guide pieces as you need to fill the edge. On my printer, 2 end...

The design is similar in concept to https://www.thingiverse.com/thing:2141857, but it is an original, from-scratch design. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.2 mm Notes: The spoolholder components...

This tool holder is specifically designed for the Anet A3 and this is a verified compatible model.

A custom-designed frame mount specifically engineered to securely hold a single SD-card for the Anet A3 3D printer.

Important note: Some heatbeds use a different pinout than the Anet A8, so make sure you connect it correctly before switching on your printer! If you find this item helpful, consider leaving a tip via Thingiverse: http://bit.ly/2szoAhU. Update...

... Link to instructions on how to hook it up to the original A8+ Board: https://h2lab.org/fablab/a8_bltouch/ (Not, mine, all credit goes to them.) Link to SKR 1.4 upgrade kit: https://www.thingiverse.com/thing:4761697 (Mine, all credit goes to me :)

Modified Hesine M-505 spool holder is integrated directly into the Anet A8 case using existing screws, effectively holding 2-3 spools of filament in place. Two M8 140mm rods and one M8 350mm rod are used to secure the assembly. ...To assemble this...

All other Anet A8 y-belt tensioners didn't fit, so I made my own. Check the pictures to see how to install. ...If you download it, after making it post a photo in the made section - it'll show that it works and if you have any issues, I can help you...

I was attempting to print ABS on my Anet A8, but ran into issues like layer separation and splitting. After researching online, I discovered that an enclosure is necessary to maintain a hot temperature. While browsing Thingiverse, I found some...

Compatible with even the largest of spools, this spool holder requires no hardware and attaches directly to the acrylic frame of the Anet A8. Profile is slim enough such that it doesn't interfere with the printer head when printing very tall objects....

Leave them commented out for the final render.) Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 mm Infill: 20% 3D honeycomb Post-Printing Clear the mounting holes with a 1/8" drill bit and the switch hole with a 1/4" drill...

Printer Settings: * Printer: Anet A8 * Rafts: No * Supports: No * Resolution: 0.15mm * Infill: 30% * Notes: + Sliced in Slic3r. + Used PLA filament that came with the A8. + Infill was 30% rectilinear infill, and rectilinear top/bottom layers were...

Included STLs are for Anet A8 extruder with Volcano heater block. To customize, you will need the dotSCAD library: download the zip archive and extract it alongside fan-duct.scad. Here's how to set up and use OpenSCAD in customizer mode. You may...

Space is allocated for an Anet v1.0 motherboard, 5-button LCD screen, 1 mosfet, fused switch, and PSU. Additional space exists for another mosfet or a raspberry PI, but modifications are required. Easy to install a pi inside, with only one mosfet...

A customized filament guide designed specifically for the Anet A3 printer, utilizing its original mounting hardware and ideal for applications where a top-mounted filament holder is employed.

This is a little mount I made for attaching a dial indicator to the print head of an Anet A8. its not perfect, but it works for me. The bore of the mount fits a gauge with a shaft diameter of about 8mm, and the little screw i use for clamping the...

This is a Y Belt Clamp designed specifically for the Anet A8/AM8. It seamlessly integrates with the stock H plate, making it an ideal solution for your printer's needs. To bring this clamp to life, you'll need to print two essential components: 1.

A simple yet effective E3D Chimera+ (air-cooled) mount is designed specifically for the Anet A8 and printers with a similar X axis setup. The 5015 blower fan mounts on the side of the printer, while a fan duct encircles both hotends to provide...

This is a basic power switch case for the Anet A8 3D printer. It can be screwed into a corner of the frame of the printer. Some notes: * You will have to drill holes through the frame of the printer and through the printed case in order to insert...

This is a low-friction filament guide designed specifically for the Anet A8. It effectively dampens rapid filament flow at high printhead speeds, distributing jerky movements over a longer time frame to account for the inertia of the spool. The guide...

I found the original didn't fit my Anet's butterfly nuts – they are fatter where the nut meets the wings. The mod adds a 2mm radius easing on the interior for more room. The bushings for the springs remain unchanged. 50% infill might not be...

You're looking for a hassle-free solution to illuminate your Prusa/Anet A8 printer without getting bogged down in soldering and other complexities. This might just be the answer for you! This is a straightforward modification that involves...

This is a small attachment I designed to hold a dial indicator against the print head of my Anet A8. It's not ideal, but it functions for me. The hole in the attachment fits a gauge with an 8mm shaft diameter, and the tiny screw I use to secure the...

This is my enclosure I built for my Anet A8 using a £5 Ikea Lack Table. I utilized some Studwork / CLS Timber to construct a mitre joint frame that serves as the bottom plate. Then, utilizing a router, I trimmed an edge so a piece of wood could fit...

This mount enables you to install the RAMPS 1.4 board by utilizing the mounting holes from the stock controller board of an Anet A8 3D printer and the stock frame. Accessories include: - 3x M3 hex nuts - 3x M3 nylock hex nuts - 3x M3 washers - 2x M3...

This is a straightforward Anet A8 filament spool holder.\r\nI designed this using Freecad, and I'm providing the files for you to modify as you see fit.\r\nModifying a freecad project is surprisingly easy.\r\n\r\nTo assemble it, you'll need:\r\n1x M5...

This kit is specifically designed for relocating the original Anet A6 full graphics display to its stock mounting position on an Anet A8 printer. The idea behind this conversion is to save money by not purchasing a new frame part, which costs 25...

I was not thrilled with the gap surrounding the LCD on my ANET A8, so I took precise measurements and quickly designed this bezel to fill in the space. It fits perfectly after giving the LCD a gentle nudge because one side was extremely tight. The...