beta65 3d models

This is a replacement canopy designed specifically for the Beta65 / 75 quadcopter. ...The Pretzel cage seamlessly replaces the stock camera mount and canopy, providing a sleek new look for your drone.

I designed a simple and modest layout for my compact Whoop Beta65 brushless drone that features twelve compartments for its battery pack.

The Battery Clip allows you to convert your UR65 or Beta65 to carry two 1S batteries. V10 is designed for use with two UR65 batteries, each measuring 14mm wide. V12 is made for use with two GAONENG 260mah batteries, each measuring 12mm in width.

I'm missing a few key steps before I can move forward, and that's the printer is currently not working and I'm unsure if it will print correctly and fit into the beta65 chassis. The plan is to print it in tpu or polipropylene. It should be secure...

Composite box for Beta65 Pro micro quad consists of three distinct components: top cover, middle body to securely hold both the quad and batteries, and bottom body designed specifically to accommodate the Kingkong Tiny X8 controller and props. These...

... version requires slightly more effort to install but functions perfectly. I believe it may also be necessary for later versions of the Beta65 and Beta75 models; however, please verify your flight controller and camera mount before installation.

This is a mount for BetaFPV Z1 Camera and VTX system for Beta65/Beta65S tinywhoop-style quadcopters. There are 2 files - one is a mount for stock Z1 camera-VTX system to put on top of BetaFPV F3 brushed controller. The stock Z1 is when a camera is...

This is a customized mount designed specifically for BetaFPV Z1 Camera and VTX systems used in tinywhoop-style quadcopters like the Beta65/Beta65S. There are two distinct files available - one serves as a mount for the stock Z1 camera-VTX system,...

This is a compact 550mAh Battery Hanger designed specifically for the Beta 65 Pro (1s) tiny whoop quadcopter. It attaches seamlessly to the existing battery slot, allowing you to fly with either the 300mAh or the 550mAh battery at your convenience.

Made a strong case for my Beta65pro2 Fits perfectly on many others in the 65mm mini quad class I specifically designed it for quads, keeping it super low profile. Please note that In the photos, mine was printed with a fuzzy skin mode in Cura but...

Just a test of my capabilities.

I've been using the Pulse 450mAh 2S packs with my Beta75X and Eachine Trashcan, but they're a very tight fit. The corners of the battery holders are turning white from stress, so I ended up cutting them off. I designed custom holders in TPU that...

I took the original design of Airmaxx23's canopy and gave it a fresh twist. I beefed up the structure by adding an extra layer of thickness and secured it with a fourth screw at the rear. ...The result is a robust build that boasts a 100% infill rating,...

A slightly revised design accommodates the larger Gaoneng 2S 450 model. I adapted a previously modified, thicker front version and returned it to its original 1mm wall thickness specification. This modification maintains the existing 3.6mm height.

This modified version of the Spiked Beta75x canopy can be found here (https://www.thingiverse.com/thing:3275140), specifically adapted for the Eachine Trashcan and Beta85X. The design is versatile enough to work with any whoop style frame when paired...

This is a modified version of the Spiked Beta75x canopy, found at https://www.thingiverse.com/thing:3275140. It works with any whoop style frame when using the BetaFPV Z02 camera / VTx combo. I added a front mounting tab and made it possible to mount...

FPV camera mount crafted specifically for a Caddx Beetle on a 65mm Whoop frame, designed as a single piece that utilizes a lone rubber band to secure both the camera and battery firmly in place. I carefully removed the slender strips of frame...

Mounting an Eachine E011 flight controller in a BetaFPV 65S frame is made easy by its design. The frame itself requires minimal trimming, as evident from the attached pictures. ...For added convenience, extra holes are included in the bracket, serving...

Small base for 65mm and 75mm tiny whoops, to allow for usb connection and accelerometer calibration. ... I built this to connect and update my Mobula 7 and Beta65s

The frame is specifically designed to accommodate a beta65 setup equipped with 65mm propellers. ...To prepare it, you should print the frame itself using PETG material, while opting for TPU when printing the lipo holder.

I had a bunch of `1S 300mah` batteries from my `BetaFPV Beta65S`. The problem was that it's not possible to put batteries, they are about 1/3 smaller than 450 mah. This solves the issue. ...Batteries sit very tight.

Small maintenance base to connect usb to tinywhoops and keep them flat. ...By using this i can connect betaflight and do accelerometer calibration. I designed thjis for my Mobula 7 (75mm) and Beta65s (65mm), they both fit very well.

... BetaFPV frame designed specifically for 8.5 x 20 mm motors. ...You can easily adapt your Beta65 or Beta75 frames to accommodate 8.5 mm DC motors and 55 mm props. ... I've also included the SLDPTR Solidworks CAD file for those who want to customize it.

For frames: Beta65, Meteor65, Mobula6, Mobula7 and ect. Protects Flight controller from side crashes. Protect camera pcb from top crashes. Camera angle about 22,5°-25° fits cameras: CADDX ANNT Lite & Foxeer Pico Razer Place some foam...

... BIT TOO COMPLEX TO SCREW IN SOME CASES. I ORIGINALLY DESIGNED THIS FOR A BETAFPV 75X BRUSHLESS WHOOP BUT IT WILL FIT ANY TINY WHOOP FRAME, SUCH AS MY BETA65S AND BETA75X. ... THE ANGLE IS SMALLER THAN THE ORIGINAL MOUNT, 35° SEEMS TOO STEEP TO ME.

Modified the drone tray insert to fit seamlessly with the Beta65 frame, also ensuring compatibility with the UR/UK/US65 frame. ...Added an extra layer of versatility by incorporating a thin tray that sits atop the drone trays and slides effortlessly...

Edit it online https://www.tinkercad.com/things/4x6VxkWjZiKI just need a new Beta65 HD frame because I broke mine, found this one on yeggi somewhere and had a crack at remixing it ✌ ####WARNING#### may not be perfect, I mean it's only a starting...

###Hardware:### Frame: Beta65 frame Motor: 080x motors Lipo: 300mah X2 VTX & camera: any one you used for a tinywhoop, I used a BETAFPV Nano HD Camera that's why it's a little bit heavy FC: any AIO tinywhoop FC supports to 2S Screws: motor screws...

Based on BetaFPV's Beta65 quad. Easy print design that prints without supports. **Update 7.3.2018** There are two versions of this skeleton canopy available. Fat - the normal one for most cameras, which you should use by default. Slim - a version...

I used the following parts for my build: * [Beta65 Pro Frame](https://betafpv.com/collections/brushless-frame/products/beta65-pro-micro-brushless-whoop-frame) with the [low profile mod](https://brushlesswhoop.com/beta65-low-profile-mod/) * [BetaFPV...