big tech tree 3d models

This case fits the Big Tree Tech SKR 1.3 and 1.4 boards and attaches to 2020 extrusion. Nuts and bolts required: M3 10mm x 1 M3 14mm x 2 M3 25mm x 2 M3 20mm x 4 M3 Square Nut x 9 M4 10mm x 2 M4 T-nut x 2 All parts already orientated for best...

This case fits the Big Tree Tech SKR 1.3 and 1.4 boards and attaches to 2020 extrusion. Nuts and bolts required: M3 10mm x 1 M3 14mm x 2 M3 25mm x 2 M3 20mm x 4 M3 Square Nut x 9 M4 10mm x 2 M4 T-nut x 2 All parts are already oriented for the best...

Here we have a mounting bracket to support the Big Tree Tech 'Smart Filament Sensor' above the Micro Swiss direct drive extruder kit. Fix smart filament sensor to bracket using 2x screw and washers supplied with sensor or spares that came with...

I didn't like how the CR-10S electronics and spool holder aren't integrated into the printer. It probably helps with vibration since their stock fans and electronics make so much noise and vibration. After upgrading to SKR v1.4 Turbo with TMC2209...

I used RomaAquatics version as an inspiration. Changed the length and added two screw holes so it fits my setup. ... Can be printed with support for the bridge overhang.

This is a remix that has a recess to move the screen closer to the outside face of the stock electronics case. There's also cut outs for the SD card and USB ports to make them usable with the screen mounted, though you will have to open the case to...

Benefits from being printed at smaller layer resolutions for dimensional accuracy.I printed this at 0.1mm.Infill recommended at least 25% for rigidity.

So i took the plunge and bought a filament sensor thingy from BTT, So i needed to mount it. I have incldued the design file, this was done use designspark mechanical - its free. So if you want to mess around with it. ...It bolts to the frame using...

BTT relay bracket Adaptor bracket to mount a BTT relay to a 35mm SSR DIN Rail Snap Clamp

<p>I was looking for a way to fasten the filament runout sensor I bought from BigTreeTech to my Voron0.1 that I am building. I designed this bracket for the purpose. To use it just remove one of the 6 mm M3 screw that you are going to replace with...

I remixed this case to remove the duct above the drivers, as i found in my installation it did not fit properly. I redesigned the lid to receive 1 fan on the end opposite the board, to help draw air across the drivers. Used M3 bolts to hold...

Screen case with back plate to fit BTT TFT35 v3.0 to a Geeetech A20/M/T printer Remixed from BigFunkyMan https://www.thingiverse.com/thing:3954074

Original model created by PrintKing94. I had issues with the frame adapter's screw holes not lining up. I remixed the STL so that the sockets line up perfectly on my SKR 1.4 turbo board. There is one small issue that is unavoidable. The risers...

I have a BMG Mini Extruder and I felt the filament guide for this mount would get in the way and be misaligned with my extruder, so I removed it and decided to share it. ...The bottom chain link connector is for the normal cable chain size, and the...

<p>I loved Zachary's model however noticed the new V1.2 of the BTT EBB36 board is larger and the model doesn't fit the board, I recreated a new version in Fusion360 for the new dimensions and it works a treat :)&nbsp;</p>

Couldn't find a good place to put the BigtreeTech 5" HDMI screen with a raspberry pi, so in this design you can mount it on the top 2020 extrusion bar or with a Ender 2 Pro I have included a special mount. Included a 40mm fan guard for mounting...

I have been using the wonderful mount by Chris_Neale at https://www.thingiverse.com/thing:4683117 but wanted to switch to a Voron style blower and found the mount wasn't tall enough to clear the housing. I also cut a hole in the side because I have...

This is a simple mount for the BTT SFS v2 that I made for my Voron 2.4.It mounts to the frame with a single m3 screw.You will need longer m3 screws to secure the SFS as the supplied ones are too short for the mount.

<p>I made this model so I can mount a BTT u2C to my klipperized Anycubic Chiron. &nbsp; This will work with just about anything, though. &nbsp;I now have it installed on the Chiron, a modified VzBot, and a rat rig V-core.&nbsp;</p><p>This case is...

Trees may be essential in our lives, but nowadays, it's gears that are just as fundamental. "TechTree" embodies this idea. Interpreted another way, it's a call to action - "Go Green! Save the Planet". In this design, gears replace tree leaves and can...

I'm creating a massive tree structure, measuring 900cm x 800cm in size. I've carefully attached an LED strip to the back of this giant tree. To assemble the parts, I used superglue. ...If you're unsure about how to put them together, just check out the...

Elevate your experience with the exclusive, custom-made big gear by eMotion Tech. ...Upgrade now and replace your current wade gear for enhanced performance!

You can combine two Big Shoota high-tech dakka mechanisms to create a powerful Quad-Big Shoota-Dakka system by mirroring one and gluing it side by side. Each mechanism is fully compatible with my Big Shoota Barrels, which are available on...

Big tree good solution for park and kidsplace.

A cartoon-style three-dimensional tree model is being designed.

I planted that massive cherry tree a while back during my internship at Rockodile Games.

I've created some massive, towering trees reminiscent of those found in the rainforest, complete with sprawling canopies and a mix of gigantic, dominant trees alongside smaller ones that add depth to the environment. ...These trees are specifically...

Storm-battered trees stand tall, their branches still verdant, as revealed through a drone and mirrorless camera's 966 photographs used to create a photogrammetry model.

... attached to its branches. A mesmerizing display of lights emanates from five miniature, flashing LEDs that are strategically mounted on the central support beam. The tree itself was printed in a spiral pattern using a precision 1mm nozzle.

People gather around a massive Christmas tree, its branches adorned with colorful orbs and a shining star. The star and the ornaments are securely fastened to the tree using strong adhesive. ...A string of five tiny 5 mm flashing LEDs provides the...