big trak mini 3d models
156752 3d models found related to big trak mini.cults3d
This is my new tiny trak design using two N20 motors, and since i like compactness, both are in the back, leaving a lot of room in the front for electronics and camera. All that fits into a body of only 20 x 30 x 63mm. I used a Wemos D1 Mini and an...
thingiverse
This is my new tiny trak design using two N20 motors, and since i like compactness, both are in the back, leaving a lot of room in the front for electronics and camera. All that fits into a body of only 20 x 30 x 63mm. I used a Wemos D1 Mini and an...
thingiverse
**Introduction** ============= This is a servo driven tiny trak FPV tank with the possibility for operating on 1S or 2S and an optional OSD. It is built as one unit that when finished never has to be opened, because it can be charged, turned on and...
thingiverse
... on top with a regular pan tilt bracket. This build was frustrating as my mini rx crapped out a couple of times and i fixed and reglued everything. After that my voltage booster borked. ...So it doesnt look as clean as it was before.
thingiverse
Customized version of https://www.thingiverse.com/thing:9602 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=9602
grabcad
Big Boss Mini Seat Ver. ...(for challenge Extreme Redesign: Art, Jewelry and Architecture) suitable for 3D Printing .STL.STEPhave fun
thingiverse
Boots with a pattern on the sole here: https://cults3d.com/en/3d-model/various/mini-big-red-boots Do you want to sell prints of my designs, get all my designs for $8, or just support me? ... Check my patreon page: https://patreon.com/bigovereasy ...
thingiverse
... and are friendly with wet erase. Hopefully they can be of use to you as well. This mini comes in the following sizes -Tiny/Small -Medium -Large The corresponding base for this miniature can be found here https://www.thingiverse.com/thing:5630084
pinshape
This case holds 10 cigarettes, the most of any SMOKESNAP and stays shut with a mini bic lighter rather than a normal one, to remain slim. Lighter slides out and pops in; never be without your flame again. ...Please Visit: www.facebook.com/3DBROOKLYN...
cults3d
This case holds 10 cigarettes, the most of any SMOKESNAP and stays shut with a mini bic lighter rather than a normal one, to remain slim. Lighter slides out and pops in; never be without your flame again. ... Please Visit: www.facebook.com/3DBROOKLYN ...
myminifactory
This case holds 10 cigarettes, the most of any SMOKESNAP and stays shut with a mini bic lighter rather than a normal one, to remain slim. Lighter slides out and pops in; never be without your flame again. ... Please Visit: www.facebook.com/3DBROOKLYN ...
thingiverse
I created this Tiny Trak frame to hold a Flysky FS-GR3E or a Flysky FS-iA6 receiver and a 500 mah 1s LIPO battery. This frame is a LOS model you can find the FPV version here: https://www.thingiverse.com/thing:4010657. This frame also contains a...
thingiverse
This case holds 10 cigarettes, the most of any SMOKESNAP and stays shut with a mini bic lighter rather than a normal one, to remain slim. Lighter slides out and pops in; never be without your flame again. See more at:Instagram:...
thingiverse
Kastaplast Big-K Mini Marker. Designed for Team Kastaplast, Kastaplast Exclusive, and fellow kasta fans alike. ... NOT FOR COMMERICAL USE side note: Please don't be that person online offering to print these for monetary gain LET'S KASTAPLAST!
thingiverse
This is a 140% size expansion (Big Brother) and remix of the Mini Monster Willy. I printed the original, and while the grandson liked it, it was a real PIA to clean off supports, and nearly impossible to do so without damaging the steering wheel...
thingiverse
This will replace factory spooler of the Wanhao duplicator i3 mini. Just a few tweaks on the i3 mini spooler by plantus. ...Changed to a right hand thread, and scaled down the tube size to better fit the filament reels.
myminifactory
I found all the existing "big" spool holder designs to use too much filament have some other design flaws which I wasn't happy with, but I loved the spool holder that came with my printer for the smaller reels. This design is basically identical to...
thingiverse
I found all the existing "big" spool holder designs to use too much filament have some other design flaws which I wasn't happy with, but I loved the spool holder that came with my printer for the smaller reels. This design is basically identical to...
thingiverse
Parts list: * Frsky D8 PWM receiver * DasMikro 2S6A speed controller * Wolfwhoop WT03 FPV camera * Yosoo Mini DC 6V @ 300 RPM N20 motor (2x) * 400mAh 2S JST battery * Lego small treads X939 (2x) * Lego small wheels 55981 (6x) I used the N20 hubs and...
sketchfab
Working on redesign of Battle Trak form Rock’n’Roll Racing for Rertrogasm competition.
thingiverse
*(I salavage mine from an old A2217 brushless motor)* * Super glue * TP4056 Charging module * 3.7v to 5v Step up module.\ * Switch KCD11 (https://www.aliexpress.com/popular/kcd11-rocker-switch.html) Print Parts: * Top * Bottom * 4x Battery Mounts *...
grabcad
Case quad trak hitch for Reynolds scraper, by removing the black clevis agricultural hitch attachment you can then attach to a Reynolds land scraper.
thingiverse
Components to build a FPV Tiny Trak, also look at https://www.thingiverse.com/thing:2935413 which uses the same Lego tracks
cults3d
Components to build a FPV Tiny Trak, also look at https://www.thingiverse.com/thing:2935413 which uses the same Lego tracks
cults3d
Accesories designed (not scanned) for Attak-Trak vehicle from Masters of the Universe vintage toyline. ...Includes: - 1 side laser - 2 gears
thingiverse
This is a 32mm scale miniature Attack Trak from the Heman and the Masters of the Universe cartoon. Scaled up from the last post for a better fit to the miniatures out there and also made track assembly easier. ... Enjoy!
thingiverse
Building Instructions (Coming Soon) ------------------------------------------------------------------------------------------------------------------- INTRODUCTION: (OPTIONAL READ) - TL;DR: I'm a noob, tiny traks are cool, build one. Hello...