bigtreetech skr v1 3 3d models

Its a slightly unconventional position but it works well and I was able to use the original ribbon cable, with some new terminations until I get to rewiring the entire thing.It should work with the SKR 1.4, 1.4 turbo, and the new SKR3 since they all...

Hi, This is a compleet redesign of my original "Ender 3 Pro SKR 1.3/1.4 (Turbo) Front Housing". Because I had notices there is significant vibrations because of the fan and since the centers are not in any way connected this sometimes could be...

This case is designed for BTT SKR v.1.4 + Raspberry 3 model B+ (use pc screws to secure the boards to the case) 120mm standard PC case fan. Every other extensions (f.e. buck converters) has to be secured with hot glue. Bottom part is ready for...

This case is designed for BTT SKR v.1.4 + Raspberry 3 model B+ (use pc screws to secure the boards to the case) 120mm standard PC case fan. Every other extensions (f.e. buck converters) has to be secured with hot glue. Bottom part is ready for heat...

The plate will securely hold an SKR 1.3 or 1.4 board, a 24v hotbed mosfet, and a Raspberry Pi for seamless Octoprint functionality. This mounting system is versatile enough to work with other Davinci models as well. Computer screws and stand offs...

Housing for a SKR 1.4 (turbo) with TFT35 V3.0, Mosfet and voltage converter on the Ender 3 (Pro). It is attached to the left of the profile with 4 sliding blocks. The components are cooled with 2ea 80x80mm fans. I chose suoer silent fans with...

You will need to extend your wiring to make this work on a standard Ender 3 as the wiring harness is a little snug. I also simplified some of the geometry, namely the rails, as they gave me endless grief getting everything to fit cleanly, it...

I did not put it, so I added a cap for it. Instead of the PSU front cover, a chassis for SKR 1.3/1.4 and Raspberry Pi 3 is installed. The chassis has 6 attachment points for greater rigidity: 4 standard holes for the front cover plus two drilled by...

A duct designed for drivers cooling a 40mm fan, compatible with MKS Gen V1.3 and V1.4 boards, provides optimal installation and removal. Notably, cutting along one side of the support enables easier access. This duct is specifically tailored for The...

Ender 3 Pro Front Case for EZBoard Lite, SKR Mini E3 and Original Motherboard. You can also check Raspberry Pi 4 Front Case: https://www.thingiverse.com/thing:4285787 This is a remix of Chuck Hellebuyck's idea from...

I've upgraded the original controller to an SKR 1.3 and also wanted to use Octoprint. The separate screen controller, Mainboard and the Raspberry Pi was going to need housing somewhere, as well as cooling with the switch to TMC 2208 drivers. The...

I've upgraded the original controller to an SKR 1.3 and also wanted to use Octoprint. The separate screen controller, Mainboard and the Raspberry Pi was going to need housing somewhere, as well as cooling with the switch to TMC 2208 drivers. The...

Remix features: -Added SD card adapter slot -Added cover for screw holes (This is optional) -Small cutout for z-stop wire to go through the case cover ***Note the micro-USB on SKR board will not be accessible as I don't intent to use octoprint with...

couldn't find anything so i modified Stonecold's excellent Bear case (https://www.prusaprinters.org/prints/22319-mk3s-bear-btt-skr-v14-case) to attach to the holes where the Z-endstop used to be. Fits like a champ.</p> <p>The original (pictured)...

This is a remix of the base case from Stonecold's excellent Bear version I found on PrusaPrinters: https://www.prusaprinters.org/prints/22319-mk3s-bear-btt-skr-v14-case I'm upgrading my Wanhao Duplicator i3 v2.1 printer and needed a box that would...

This is the SKR version of my RAMPS, Pi and MOSFET Tray. Use this with This IEC Power Port to XT Connector to make your power supply external and upgrade your CR-10. This fits any Raspberry Pi 2 and up or any matching footprint SBC. Use an...

remix of the Tronxy X5SA board case by Clooney i use this case because i have made a coolling tunnel for the skr which fits exactly (look at the picture withe tunnel) i have add a second hole at one holder for my pro groundplate the one cable hole is...

remix of the Tronxy X5SA board case by Clooney i use this case because i have made a coolling tunnel for the skr which fits exactly (look at the picture withe tunnel) i have add a second hole at one holder for my pro groundplate the one cable hole is...

The SKR Mini Board is currently equipped with approximately 90% of all required parts and details.

(https://www.thingiverse.com/thing:4639576/files) The standoff location is correct for the SKR Mini E3 v3, but the plastic tabs for the heatsink stick out too far below the board. He also had forgotten to make a cutaway for the cable chain...

Removed internal fan mount as it interfered with the SKR Mini E3 due to it's larger width when compared to stock Creality mainboards and also widened the side ports for the SD card and micro USB slots. I also added screw holes to mount the mainboard...

(https://www.thingiverse.com/thing:4639576/files) The standoff location is correct for the SKR Mini E3 v3, but the plastic tabs for the heatsink stick out too far below the board. He also had forgotten to make a cutaway for the cable chain opening. ...

This is the SKR version of my RAMPS, Pi and MOSFET Tray (https://www.thingiverse.com/thing:3966761) Use this with This IEC Power Port to XT Connector (https://www.thingiverse.com/thing:3800991) to make your power supply external and upgrade your...

I've upgraded the original controller to an SKR 1.3 and also wanted to use Octoprint. The separate screen controller, Mainboard and the Raspberry Pi were going to need housing somewhere, as well as cooling with the switch to TMC 2208 drivers. The...

Mellow Fly TFT V1 3.5inch screen mount

This is an MCU Card for Thermocouple V1.3

So I originally printed out the SKR MINI E3 V3 Case created by MrTeliP, but when I installed by SKR Mini E3 V3 board it wouldn't sit flush in the case by either 1mm on one side, or by a 4-5mm on the other side.It looked like with my board, I'm not...

Work in progress V1 - With external connections V2 - No external connections Added: - Raspberry Pi4 B on right side; - Up to 4x Buck converters; - More supports on sides; - Extra air flow underneath boards; - Less "walls" = more room for wires, less...

<p>I maked first black PLA+ but I broked, after maked black PETG. ...I used 0.4 nozzle @ 0.3 layer.