bike cable clip 3d models

Replacement of bike cable clip

Simple bike cable clip based on clips from Moustache ebike.

Customizable clip for a bike cable.

Clip to hold bike cable, three versions : Brake-brake Brake-gear Brake-gear at 90 degrees

I lost one of the cable clips of my Stevens bike (2018 Lite Tour) and designed a replacement part. Now the cable stays in playce again. Clip just snaps in the clip mount on my bike. You can see there are minor differences between the original one...

Clip to hold bike cable, three versions : Brake-brake Brake-gear Brake-gear at 90 degrees 9 feb 22 added two versions without B or G sing Brake-brake_NO sing Brake-gear_NO sign Print Settings Supports: No Infill: 100% Notes: Made in Abs, the fit is...

HI, this cable clip works perfctly with cables diamter 4,2 mm and 5,2 mm like in the Specilized Epic.

HI, this cable clip works perfctly with cables diamter 4,2 mm and 5,2 mm like in the Specilized Epic. ...

This is a clip designed to hold one 5mm (brake line) cable, and one 4mm (derailleur) cable housing. Use one for the left side of your bars, and one for the right. ...Keeps your lines organized and rattle free.

This cable clip was inspired by a couple of similar concepts found here. What makes it special is that it is universal: it can fit any tube, you only need a tie-wrap. Fits standard shifter and brake cable housings. ...Fits up to 5mm wide tie-wraps.

 Print two and clip them on in opposite directions as shown in photo for a more secure fit.There are three different diameters of clip as it's a little bit of trial and error to get the right size for your cables depending on your printer and...

... on my filament. Made some ajustments to cable slots,made one smaller to work better with the shifting cable and one larger to hydraulic brake hoses. After some shots i got a good fit and easy to print model. ...And it worked on my generic PLA.

So i decided design a new one using with some little differences to print well on my filament.Made some ajustments to cable slots,made one smaller to work better with the shifting cable and one larger to hydraulic brake hoses.After some shots i got a...

Rotating cable clip for bicycle cables, fits Shimano and other brands of lines, tried to size it so it fits smaller and larger lines. Fits snug on hydraulic lines and more loose on cable actuated lines. This is somewhat similar to the clip that...

use double sided tape to attach to bike frame and snap cable housing in to secure loose cables

;-) My Specialized Hard Rock has three cables running along the underside of the top tube and I didn't want to keep cutting the zip ties holding them on every time I swap my dropper post to/from this bike. This clip can hold all three cables and is...

These are cable clips designed to be stuck to your bike frame with thick double sided mounting tape which can hold your shifter cable housing or brake hose in place. These are made for 4mm shifter cable housing but can be scaled to get a proper fit...

I found some cable clips here on Thingiverse, but wasn't quite satisfied with them, so I designed new ones. Check your cable diameters. There's a version for 5/5 and 5/4mm cables. There's also the FreeCAD files, if you want to make modifications.

All in the title... ...one to clip 2 cables together, the second to clip 1 cable to the frame. Made with PLA. ... Designed with DesignSpark Mechanical (files included)

Replacement C-Clip for bike cable.

Replacement C-Clip for bike cable. Prints in about 5 minutes

I managed to brake one of the cable management clips for the cable running to the motor on my Gtech e-Bike. From memory the bike has a 5mm diameter cable and M4 bolt to hold it so this might suit other ebikes. ...This is a replacement designed in Fusion...

Modded the cable clip from here: https://www.thingiverse.com/thing:2590682 in order to have additional support for a 2mm straps, you can carry a spare tube, an additional water bottle or anything you want. ... EDIT 25/01/2022: Added two more files,...

Modded the cable clip from here: https://www.thingiverse.com/thing:2590682 in order to have additional support for a 2mm straps, you can carry a spare tube, an additional water bottle or anything you want. EDIT 25/01/2022: Added two more files, both...

I redesigned this because the groove was not round.

Customized version of https://www.thingiverse.com/thing:2185517 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2185517

Customized version of https://www.thingiverse.com/thing:2185517 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2185517

Customized version of https://www.thingiverse.com/thing:2185517 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2185517

I managed to brake one of the cable management clips for the cable running to the motor on my Gtech e-Bike. From memory the bike has a 5mm diameter cable and M4 bolt to hold it so this might suit other ebikes. ...This is a replacement designed in Fusion...

A super simple cable clip for keeping the cable tidy on a front-motor e-bike conversion. Please note that this is designed to fit onto a mountain bike (MTB) shock absorber fork and may not fit a rigid fork without modification as they tend to be...