bit to gb 3d models
2094623 3d models found related to bit to gb.thingiverse
###USB to GB Link Cable Adapter Case This is a tiny case for the absolutely awesome [USB to GB Link Cable Adapter](https://stacksmashing.gumroad.com/l/gb-link) by [@stacksmashing](https://www.youtube.com/channel/UC3S8vxwRfqLBdIhgRlDRVzw). ...It is meant...
prusaprinters
This is a small protective case for stacksmashing's USB to GB Link Cable Adapter (which can be purchased here: https://gumroad.com/l/gb-link) The print comes in 2 parts - a Case, and a Lid. The Lid has enough clutch power to stay in place, but is...
thingiverse
Due to popular demand this is a remix of my [GBA to GB Cartridge Protective Case Insert](https://www.thingiverse.com/thing:3043521) for the EverDrive-GBA. **WARNING** This is a guesstimated EverDrive-GBA insert. I don't own a EverDrive-GBA to...
thingiverse
Bit adapter A standard screwdriver for a small screwdriver of electronics. ... This turns the electrical screwdriver into a screwdriver for electronics as well Recommended fill density more than 50% It is recommended 0.2 layer height for all ...
thingiverse
Square wrench to drill bit adapter. ...Print Settings Rafts: No Supports: Doesn't Matter ...
cults3d
1/4 square drive such as a ratchet to 1/4 hex which most drive bits are. A good tool to have for those hard to reach screws. ... Print with 3 perimeters 40% infill no support needed.
thingiverse
It is a part of a 3D printed electric screwdriver project, more info can be found in here: https://www.thingiverse.com/thing:5583965 I didn't try to print it without supports, printing it starting with a bit hole at the first layer is better as it...
prusaprinters
Fusion360 file contains 2 parameters that you can change to adjust it to your shaft and bit dimensions.It is a part of a 3D printed electric screwdriver project that will be published here soonI didn't try to print it without supports, printing it...
thingiverse
1/4 square drive such as a ratchet to 1/4 hex which most drive bits are. A good tool to have for those hard to reach screws. Print with 3 perimeters 40% infill no support needed. ...Print Settings Printer: I3 ...
thingiverse
... enough pressure on the spacer, it will deform and be difficult to remove. It also turns out that one of my earlier designs works just as well for this use case: http://www.thingiverse.com/thing:350118 Just customize it to "adapt" 1/4" to 1/4" bits.
thingiverse
I searched a lot on internet and couldn't find any Wiha slimBit to standard Bit adapter to use with my Wiha Speed-E or whatever. So I created it by myself on Autodesk Fusion 360. After 6 versions of testing and printing it became almost perfect. Use...
thingiverse
I needed a rechargeable screwdriver to open the screws of mobile phones, and I already had a rechargeable screwdriver with a large bit size. Despite this piece, I don't need to buy a rechargeable screwdriver for mobile phones. Tip: When the print...
thingiverse
... Structural integrity is questionable. V2: Using the original model showed that a) the circular socket was too big to get into a couple of the spaces I was working with and b) the axis of rotation was annoyingly off-centre. ...So I fixed that.
thingiverse
... ? ... The bit adapter !! And then you find yourself trying to use the small bits by hand then with a wrench. It works but it does not bring joy. There comes this adapter, brings joy back ! ... Room available for a magnet at the bottom (glue it)
thingiverse
Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130
thingiverse
Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573
thingiverse
Customized version of https://www.thingiverse.com/thing:4681765 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4681765
pinshape
:-) I have a “converter piece” from socket to bit hexagon shape in two sizes. There is a third converter piece that has a hole in the hexagon side. In this hole you can glue a piece of metal for magnetic bit holders Also I have handles or “bit...
myminifactory
:-) I have a “converter piece” from socket to bit hexagon shape in two sizes. There is a third converter piece that has a hole in the hexagon side. In this hole you can glue a piece of metal for magnetic bit holders Also I have handles or “bit...
cults3d
:-) I have a “converter piece” from socket to bit hexagon shape in two sizes. There is a third converter piece that has a hole in the hexagon side. In this hole you can glue a piece of metal for magnetic bit holders Also I have handles or “bit...