bitburger stubbi 3d models

DESCRIPTION ================--------- This is a solid piece with a continuous surface that doesn't have any separate sub-elements. It was designed specifically for the iFlight XL5 frame, but it might also fit some other frames. The space between the...

I've successfully spliced the Reaper's face onto a new body. The displacement seams are a bit rough, but they should iron themselves out once printed. I took some screenshots of the 3D model and used them as a displacement map on a low-poly mesh with...

This is my remix of a great design. I didn't need it for spraying liquids, but to repair a shaving cream can that had a super cheap plastic nozzle that shattered on a drop in the shower. Instead of not being able to use it, I made a couple of tweaks...

One leg is longer than the other so that the XT60wires can be zipties to the standoof

This is a sleek enclosure for the Sonoff Basic configured as a push button. The box is approximately 29mm deep, making it a perfect fit for gang boxes that are often crowded. This project combines innovative concepts from various makers, and I'd...

This is a can holder that fits the 33cl small Heineken ( and should fit others of same dimension ) Designed to fully enjoy the can drinking experience without having to deal with the condensation on the can of the sensation of holding something cold...

I created a swivel driver that is small, balanced, and fits in your palm for easy one-hand use; no lasers this time! Using Blender, I added superness to the design. For those who prefer a lighter version, there's also a mini paw model made with more...

Remixed directly from the source, this design has been modified to enable a seamless fit across two rail holes by removing the locator nub. ...Additionally, some interior material has been carefully trimmed away from the grip for a sleeker appearance.

I needed a simple tool with some oomph to quickly swap out hot end extruder nozzles.\r\n\r\nAs it turns out, this is basically a short-handled hex wrench that can be used for any hex-shaped tool bits. ...It's designed to fit onto a 1/4-inch square...

FPV antenna mount for TBS Triumph pro. ... 45 degrees 20mm tall from the top plate.(Check the length of antenna tails)

Tweaked to fit 3 common sizes in Australia, stretch & ease of printing by not having chamfered top or bottom, (though these options are still available in the scad file) I printed these in Vase/Spiral Mode with flexible TPU with a 0.8mm nozzle...

Tomlombardi's small Screwdriver Handle is a great design, but I found it could use an additional accessory. To solve the problem of finding my screwdriver tips, I created a handle attachment that accommodates up to 8 bits arranged all around the...

A rough hack to repurpose RX holders as a VTX antenna mount for axii-style antennas, perfect for those who need a DIY solution. Thanks for sharing this tip, Max! ... - Flakes

I experimented with various designs for an immortal t antenna mount but couldn't find one I liked, so I settled on this option. It will position the immortal-t roughly parallel to the rear arms while providing ample clearance. ...The design prioritizes...

Rear Chassis bumper for the Element Enduro Sendero HD, Can be used on SCX10 SCX10 II or anything with C RailsStubby rear bumper with tow hitch and D-Rings.Revision - I am learning OnShape and Freecad so I redesigned the rear bumper in 80, 90 and 100...

This is a versatile wrench that's perfect for working on faucets with intricate finishes. Recently, I used it to replace the worn-out washer in my tub faucet, which boasts a stunning brass finish. ...To prevent scratching the lacquer coating, I designed...

Summary This is shortened version of the V8 Slim wand designed by murat. The original was too large to print on my Prusa Mini, so I reduced it by about 45 mm. Works very well. Spring is slightly tricky to install. I used a butter knife to hold it in...

Serre câble pour moteurs ESC si besoin modifier le stl pour ajuster vos diamètres

Beer Holder for Half-Liter Cans. Depth inside: 6 inches, Inner Diameter: 1.3 inches. ... Would you like to know some manufacturers?

This is a can holder that fits the 33cl small heineken ( and should fit others of same dimension ) Designed to fully enjoy the can drinking experience without having to deal with the condensation on the can of the sensation of holding something cold...

To support my work, visit my Patreon page at https://www.patreon.com/3DPrintingProfessor. Subscribe to my YouTube channel and check out my new dualed design V2 for better printing with fewer gaps. I now sell these on Etsy; visit...

A personalized variant of http://www.thingiverse.com/thing:165857 has been created using the Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=165857). ...To fabricate this design, you can set the following parameters: notches = 1;...

This is the 106^th re-upload of the design as the former versions were delisted due to abusive individuals exploiting Thingiverse's 'Report' feature. __Apologies as I am not reposting to keep it in the current/newest list.__ <font...

This soft tip should be printed in TPU and will fit snuggly over the excellent short spout model provided by @gpace08 here. Use-case for this is for when you're using this shorter spout to dry off vehicles - the TPU soft tip adds a small layer of...

Create a compact screwdriver set with a bit holder for your cordless drill. To assemble, attach nine magnets using superglue (check out K&J Magnetics for options). Next, insert your preferred bits from McMaster-Carr's extensive selection. ...Lastly, add...