blackout mini h 3d models
142108 3d models found related to blackout mini h.
thingiverse
BlackOut Mini H Spacer 6" Height: 8mm Print 2 "Spacer-Hinten" Print 2 "Spacher-Vorne"
thingiverse
Male XT60 connector mount for Blackout Mini H quadcopter. Slides onto two rear 35mm spacers to accept female XT60 from LiPo. Hex spacer sockets are 6.1mm to allow for print swell. Pocket for XT60 will be a tight fit as designed - you will likely...
pinshape
SummarySimple mount for Mobius Action Camera on Blackout Mini H FPV racing quadcopter. Use Blackout's rubber anti vibration mounts for better image quality. ...Angle 15 degrees.
thingiverse
Simple mount for Mobius Action Camera on Blackout Mini H FPV racing quadcopter. Use Blackout's rubber anti vibration mounts for better image quality. ...Angle 15 degrees.
thingiverse
I am Building A Fearless Version of the Blackout Mini H Quad and ran into a spacer issue.... The Fearless H Brace Can Be scaled down in the Z plane by 50% to fit on the Standard Mini H. New Bumper Is a tricky print! ...Included a fearless version of...
thingiverse
This is a snap-on boot for the arms of the Blackout Mini H quadcopter frame. It provides 6.5mm (.255") of standoff of the arms to the ground, which will help act as skid plates. It also has about 2.4mm (.094") of crush zone before the frame sees the...
thingiverse
Compatible with Blackout Mini H, might be compatible with other quads but they have not been tested. If one is compatible please let me know! A good/well calibrated printer can print this with no support. 30-40% infill is ideal Use a...
thingiverse
This is a 3mm spacer for the Blackout Mini-H Quad baseplate Handy to print out a heap of these to keep as spares Customized version of http://www.thingiverse.com/thing:79944 Created with Customizer!
thingiverse
This is a vertical panel for mounting stuff (electronics, etc) that fits into the top plate and PDB slots in the back of a Blackout Mini H. It is VERY sturdy even when printed at 15% infill, and doesn't weigh much of anything when that hollow. It...
thingiverse
It is tested on my spider hex, but I think it should fit on all other Blackout copters, like: Blackout 330 Blackout Mini H Quad Hope you enjoy it! Please let me know if there's anything to make better. Using this landing gear, u will have free...
thingiverse
all up this shelf and spacers are the same distance between the Blackout PDB and top plate, this holds it in place but allows you to simply slide it off when the top plate is removed. ...Print Settings Printer: Wombot XL ...
thingiverse
This is if you fancy a 10Deg up tilt on your Mobius. Fits right where the Mobius sits with velcro or what ever you like and the Mobius on top of that. ... works perfect with the 10deg motor tilt then you will get a nice video when filming..
thingiverse
13 degree motor tilts for the Blackout Mini-H Quad 5" -Contains 2 regular and 2 mirrored tilt mounts
thingiverse
This is a 2 piece bumper for the BlackOut Mini H. I split the solid to make it easier to print. The Lower can be printed in a tougher material and the top can be printed in a clear material to act as a lens. ... If a lens is only wanted then install...
thingiverse
New Bumpers and spacer for the standard Blackout mini H quad Print bumpers with support. ...Printed with translucent ABS for a Glowing effect.
thingiverse
This is a 12 degree FPV camera mount for the BlackOut mini H. This was made for the BlackOut only. I will use rubber O rings to isolate the camera. Add an extra O ring to increase angle. Printer is down for repair, Had a friend print out a sample.
thingiverse
15º angled mobius camera mount for the Blackout Mini h Quad Originaly made by bjorntm, he gave me the source file and I've modified it acording to my needs. Thanks a lot man! Instructions Printed in...
thingiverse
Designed for Blackout Mini-H Quad with 5" arms. Probably dose not work with other frames. Motor pattern based of Untested Prototype layout. ...http://untestedprototype.com 10° forward angle A full set consists of: 2x Normal 2x Mirrored This...
thingiverse
A Collection of skid plates for the blackout mini H Print with your favorite material.... Mix and match colors to help orientation for line of site flights. Don't buy the copies and print the originals. Find a maker space or contact me if you don't...
thingiverse
Keeps antenna away from Carbon Chassis. ...Replaced plastic screws with Aluminum button heads M3.
thingiverse
Cover the ends of your arms and protect your nice carbon fiber. print out with your favorite material! ... Instructions Currently trying 50% fill
thingiverse
You Just bought those EXTRA thick arms for your Mini H BlackOut? Put on your slippers so you don't scuff up your toes! ...These are extra thick and comfy ;) Going to print out of Polycarbonate for the glass slipper effect!
thingiverse
I made up a minimalist antenna mount for one of my blackouts to keep the stock look. Replaces the 2 front flight controller posts. ...Sized to fit my FRsky D4R-ii
thingiverse
... and the PDB or use M3 nylon bolt with a nut through the center hole. This design is based on ZMR250 camera mount by @czuryk. Thanks! For Blackout frame only, will not work on ZMR250 because of the different distance between the front spacers.
thingiverse
Customized version of http://www.thingiverse.com/thing:1068400 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1068400 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:1068400 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1068400 Instructions Using the following options:...