blade 230s helicopter 3d models

Blade 230s helicopter main rotor head linkage pair

replacement skids for the blade 230s helicopter and maybe other models Print Settings Printer: XYZ davinchi Rafts: No Supports: No Resolution: fine or excelent Infill: 35 to 50% Notes: the finer the print the better they are, and flip the part for...

Hi, I created a windscreen wiper for a Blade 230s RC helicopter that fits nicely to the www.heli-scale-quality.com body for that kind of helicopter. ...Pictures and whole description about that nice helicopter can be found under...

This landing gear for the Blade 230s helicopter is angled at 2 degrees to make the tail sit about an inch higher than the stock landing gear. You'll need to print 2 "Brackets" and 2 "Skids". Print the brackets on their sides and use supports...

This print is for the Blade 230s Helicopter but may work for others with the same type grommet and post canopy connectors. No modifications are required to the helicopter. Just remove the two rubber grommets from canopy and put them in the 3D...

Here's a part for the Blade 230s Helicopter. This is a pitch link for the swashplate to rotor head blade grip. If the link is too tight or too loose on the balls try scaling the print down or up a few fractions using whatever slicer you prefer.

Landing Gear for Blade 230s

Landing gear replacement for the Blade 230S

Blade 230s replacement skids. the skids are about 1g lighter and just as strong maybe stronger. I like to looks better. they are about 15mm wider and 2mm taller. they are a lot cheaper. $1.20 for the aluminium skid tubs. K&S 5/32 #8103. cut tube to...

This is a replacement frame kit for the Blade 230S. You can still use the original electronics. 4 M2x10mm hex bolts and nuts are needed for clamping the tail boom. The nuts must be inserted\pressed in the right frame side. I printed all frame...

made a vertical fin for the 230s that is more appealing. ...if printed with .6 top and bottom its actually lighter than the oem.

... ...Blade 230s. i purchased a set of aluminium and carbon fiber skids from lynx for my 230s. I also purchased a replacement set of plates. got bored today so i created a block for the spare parts and bolted them to the other heli. looks good to me.

I designed the landing gear for the Blade 230s V2. It is a perfect fit. I printed these gear in about 4 hours. My gear is printed from ABS but other material will work. There are 3 files. They include a Landing Gear mount bracket legs that will...

This is a simple and light replacement landing gear for the Blade 230S. It might look flimsy, but the goal is to make it fast to print and disposable. It can be used as replacement for the original landing gear or in conjunction with the replacement...

this is a swash level tool for a blade 230 s helicopter, and maybe others Print Settings Resolution: fine Infill: 50% Notes: i use the XYZ davinchi 1.0

Blade holder for the 230s. you will need to sand to fit for PLA. ...TPU simi-flex is no sanding needed.

Landing gear for Blade 230S V1 or V2. I crashed and designed these. Use some CA to glue the skids to the gear. I printed with no support and you can see the bridging effect on an Ender 3. ... Use support if you want to clean that up :)

Blade 230s tail motor mount and fin as one unit. Its a plastic copy of the microheli light weight unit. It is about 1.2g lighter than the microheli unit. Almost 3g lighter than the stock unit. This should help with the tail weight. 3g off a 10" lever...

There are some Scale kits for the Blade 230s, which are very expensive but also extensive. But there are also simpler kits that are affordable. This is where the 3D printing comes in. Most parts can be made of PLA. Unfortunately I only have the...

Replacement vertical tail fin for the Blade 230s. Carbon fiber/ABS (stronger, cheaper, and lighter). holes need to be enlarged to 5/64. i will fix this in the next release. cut 2mm carbon fiber rod to length glue in place. you can strengthen the...

This is a blade 230s tail boom slotting jig. put one peace of the jig on each end of the tail boom after boom is cut to length. then snap the jig down flat to the work bench. this will align the holes for the slots. K&S #9807 aluminium tubes are used...

R/C helicopter blade

Electric Camera Helicopter replacement blade

A typical helicopter blade with different airfoils

This is my helicopter blade. Made for 3d print. Wont work properly! ...(own measurements)

Use A Helicopter Blade Design In Surface very Creative Item Design

XK K110 blade, ou pale d'hélicoptère XK K110

This is a test model for a 3D printable blade for the Blade CP RC helicopter. I am really good at plowing it into the ground and though this may solve the replacement blade problem! Enjoy! If you like this project and wan't to learn more about making...

hope u like it

Designed to fit into kingdallen's Canopy Quick Connect: https://www.thingiverse.com/thing:4617671