blade 300 cfx 3d models

abbc

for the Blade CFX 180 this blade holder works really great. ...also it is made out of tpu or Ninja flex.

Protection for the RC Blade 270 CFX helicopter that prevents the LiPo from going against the engine.

This is actually for a stretched 270 CFX to 325mm blades and a 373mm boom. Just over 27 cubic inches of material when printed solid. ...The smaller parts are printed inside the larger.

My rendition of the Blade 180 CFX skids for replacement purposes. It's not identical to the original, but it was a modified version of another skid design I made. ...You will need to print supports for this.

This is a swashplate leveling tool for the Blade 180 CFX helicopter. ... The center hole will need to be reamed out to 4mm to make a snug fit on the main shaft.

My rendition of the Blade 180 CFX skids for replacement purposes. It's not identical to the original, but it was a modified version of another skid design I made. ...You will need to print supports for this.

Light Tail Rotot Protection for Blade 180

This is a replacement tip for the 180 CFX helicopter torque tube tip (which always shatters in a crash). Print it, then ream out the center hole with a 1/8" drill bit for a snug fit on the torque tube shaft. Be sure to install the cross pin to keep...

This is a replacement tip for the 180 CFX helicopter torque tube tip (which always shatters in a crash). Print it, then ream out the center hole with a 1/8" drill bit for a snug fit on the torque tube shaft. Be sure to install the cross pin to keep...

I wanted to be able to print out a set of fins for my Blade 300X helicopter that maintained a somewhat stock look, allowing me to control the color and material. I drew up this set of fins and printed a yellow set in PLA. I found that I could...

http://www.thingiverse.com/apps/customizer/run?thing_id=749887 Instructions Using the following options: wall = 1 fontname = Ultra shift_font_percent = 0.07 do_shift_font = no base_radius_add_percent = .1 basethickness_percent = 0.1 textsize = 25...

http://www.thingiverse.com/apps/customizer/run?thing_id=50885 Instructions Using the following options: Font = write/orbitron.dxf hole_radius = 5 icon = 1 icon_size = 10 icon_rotation = 0 font_two_size = 30 font_one_size = 60 manual_length = 100...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/bfK1w6QHO97

This is a larger "training" skid for the Blade 180 CFX heli to help new pilots feel a bit more confident in their heli practice. It uses a 3mm carbon rod. ...Currently this file has no drill hole location yet, but I'll be updating and revising the...

This is a larger "training" skid for the Blade 180 CFX heli to help new pilots feel a bit more confident in their heli practice. It uses a 3mm carbon rod. ...Currently this file has no drill hole location yet, but I'll be updating and revising the...

This is a larger "training" skid for the Blade 180 CFX heli to help new pilots feel a bit more confident in their heli practice. It uses a 3mm carbon rod. ...Currently this file has no drill hole location yet, but I'll be updating and revising the...

Accessoire tube torque ABS Print Settings Printer Brand: CEL Printer: Robox ...

Utility Knife Blade- Stanley 11-300

The wilde version of the Blade is my submission for SUPERCAR SYSTEM B2 SPIRIT 300, the concept take no reserves in using LMP aero style but tries to stays well on street also. The initial Blade concept had already a lots of downforce features...

There are some Scale kits for the Blade 230s, which are very expensive but also extensive. But there are also simpler kits that are affordable. This is where the 3D printing comes in. Most parts can be made of PLA. Unfortunately I only have the...

COMPUTATIONAL FLUID DYNAMICS

Customized version of https://www.thingiverse.com/thing:3649189 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3649189

new muzzle for gamo cfx

Hier ein Modell-Ständer für ein MST CFX und CFX-W

Loading funnel that locks for the boundless cfx or cfc for easier loading

Customized version of http://www.thingiverse.com/thing:340321 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following options: BlockWidth = 1 Name = 300! ...BlockLength = 4

I didn't see much from the movie "300," so I'm uploading this. Not overly useful and not tested. Printing one right now. If you extrude it enough, you could maybe use it as a pencil holder? Traced in Illustrator and extruded in Inventor. If you...

Simple Stand for the MST CFX-W. ... For one Stand you need to print the mstcfxwstands.stl 2x You need 2x M3 screws.

This is for a MST CFX. I made this after trying out the other one on here but found that it did not fit with my CFXs dimensions. ...