blade 350 qx 3d models
40500 3d models found related to blade 350 qx.prusaprinters
This is a two part mount for the Blade 200 qx quadcopter. I wanted a camera mount that faces down, so I designed one. It is in two pieces, so you can use the main mount as a platform for your own designs.</p> <p>This may not need supports, depending...
thingiverse
simple clip-on-mount to to put 2x 5mm-LED's to the nano QX FPV camera mount. Just print, take 2 LED's and the corresponding resistors, solder everything together and plug it into the LED holders... Simple to clip on/off as needed. ... The power...
thingiverse
V1 of my small quad frame for NanoQX components from Blade. Still working on it but it flies very good so far! ... V2 ONLINE NOW!!http://www.thingiverse.com/thing:318081 Print with no support and 0,2mm Layer - Infill 20%
cgtrader
... this is speed deamon you have to fly. Also comes with starting block to help you fly in self stabilizing mod inside of house or office. If you need option with straight motors just let me know. this frame work with all oryginal blade nqx parts
thingiverse
I Broke my origional frame during firs 3d flight and didnt like the idea of relacing the whole thing because one arm broke. Looked around and didnt like the printable frams i found so iu went ahead and designed my own. This is frame 2.4 as i have...
thingiverse
Remix of http://www.thingiverse.com/thing:809885 to fit the Micro Motor Warehouse 6mm motors. It is set to 6mm hole, but the motors are 6.2mm in diameter, so you need to bore out a little with an xacto knife to fit properly. ...Print Settings Printer...
grabcad
Saw blade for 5axis CNC machine 9 meters long. ...visit inal.com to see it working
thingiverse
This is based on http://www.thingiverse.com/thing:617052 but is fixed. The original version of this model was not watertight and therefore did not print correctly. This prints properly (the lid is a bit tight though, might rework that in the near...
cults3d
This is based on http://www.thingiverse.com/thing:617052 but is fixed. The original version of this model was not watertight and therefore did not print correctly. This prints properly (the lid is a bit tight though, might rework that in the near...
thingiverse
This is e repaired version of KiLLiN-TiMe's version (https://www.thingiverse.com/thing:1266503). ...The lid didn't print correctly, so I repaired this and now it prints fine.
thingiverse
J'ai créé ce chassis pour remplacer l'original de manière à pouvoir incorporer une caméra avec émetteur pour faire du FPV. J'ai retiré 2 leds pour gagner un peu de poids. Et tout fonctionne ! ... Bons vols
grabcad
DIY quadcopter for FPV no props view Parts from grabcad.com : Tiger MT2814 GoPro Hero 3 HD Camera with the Frame 9x4.7 Propeller credit to: garbungel for more info about the model http://forums.openpilot.org/topic/20755-qx-9-full-carbon-fpv-frame/
pinshape
Based on the frame layout of the FireFlo, I wanted to shave some weight off a mono-deck for nano QX board and camera, paired with low-cost Hubsan 7mm motors & props. The result is this Gnat QX, with the frame weighing in at a mere 3g. AUW...
thingiverse
Based on the frame layout of the FireFlo, I wanted to shave some weight off a mono-deck for nano QX board and camera, paired with low-cost Hubsan 7mm motors & props. The result is this Gnat QX, with the frame weighing in at a mere 3g. AUW without...
cgtrader
Saw blade for 5axis CNC machine 9 meters long. ...visit inal.com to see it working
thingiverse
I wanted some more space for larger packs and my fpv pack and made this. ...I am still working on the camera mount for the VA1100.
thingiverse
New Version of the small frame. ... better wire support for motors more stable motor mount ( 2 Layers ) reduced weight by removing unless parts Instructions Printed with 2 perimeters, 2 layers...
youmagine
Frame anti obsolescence for Blade Nano QX 3D the frame is made for the more powerful engine than 8 mm). ...Simply solder the motor son on the feet pad arms The flight controller esc holds integrate with 8 mm motor in normal flight mode for 3 minutes...
thingiverse
...FR: Protège hélices pour QX 95 inspiré des Prop Guard de Boopidoo pour QX 90, retravaillées pour s'adapter à un QX95 How I Designed This HI, I used the Boopidoo prop guard as a model and reworked it in FUSION360 to add the extra length for the QX95.
thingiverse
This is a Race Quadcopter inspired frame for the Blade Nano QX. It is about 2g heavier than the original one when printed in PLA. The quad is in my opinion a little more agile than with the original frame. The stock and most of the aftermarket...
cults3d
I'm not really interested in hanging a GoPro off the 200 QX, and have no idea how it will fly with one attached on this mount, or that it'll stay attached. ...However, I need the 200 QX mount for other projects (watch this space), and this looked like...
thingiverse
Prop guards for the 180 QX quadcopter. ... added lighter/stronger versions ** new version that no longer needs zip ties: http://www.thingiverse.com/thing:566440 Instructions Print four of them and...