blade rc 3d models
60587 3d models found related to blade rc.thingiverse
This is a two blade version of the 3in spinner I uploaded a while ago.
grabcad
I made this model of my mQx to make accessories from. ...The Design belongs to E-Flite RC Blade division.
thingiverse
Blade holder for the 230s. you will need to sand to fit for PLA. ...TPU simi-flex is no sanding needed.
grabcad
A low profile, fully enclosed swashplate. I designed this rotor head a few years ago for a UAV project. This rotor head has a completely enclosed swashplate with control rods coming through a secondary stationary shaft. The rotor spins on a outer...
thingiverse
Angle of attack is nominally 16 degrees, but depends on airspeed. ... High efficiency NACA helicopter profile used, but this prop is meant for RC planes. ... 100 mm diameter.
thingiverse
Customized version of https://www.thingiverse.com/thing:2431995 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2431995
thingiverse
This plate will prevent your battery from rubbing on the brushless outrunner motor. ... Instructions Glue plate to holder and insert into slot in helicopter.
cults3d
... this propeller in both a push or pull configuration, that is why the hub is open on both sides. The diameter of the hole of the hub is 3.5mm and is suited for the "A2212 1400KV RC Brushless Motor." The diameter of the propeller as a whole is 150mm.
thingiverse
Customized version of https://www.thingiverse.com/thing:2431995 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2431995
thingiverse
This object is designed to adapt the RC Logger 2 digital pitch gauge to the Logo 550 SX V2 RC helicopter with the plastic blade grips.
cults3d
90 mm electric turbine, with 12-blade propeller for model aircraft, you can use the motor you prefer, I used a 1700 KV motor, it comes with a 5 mm adapter for the motor shaft, this adapter has a 8mm to hold the 12-blade propeller. and a 9mm long m3...
thingiverse
It is a rc heli mold for blade msrX helicopter Instructions I will creat the LH side soon
grabcad
3 Blade RC model propeller with alloy spinnerPlease like if you download
grabcad
General approximation of RC Helo Main rotor blade. ...Measured with Calipers and improvised to fit.
thingiverse
As part of my recycle of old RC Helicopter blades, they leave the ends exposed, and these can get wet, and thus out of balance, hence these covers that will close these ends and allow them to be waterproof.
thingiverse
Prototype 3D printed RC propeller blade, 4 3/4" overall (X2). The base is cut off leaving the 6mm X 10mm round boss which mates to the hub. The hub for 2mm and 3mm shafts and other blades are in the works and will have indexing marks to set pitch. ...
thingiverse
a snow blade as a request to a viewer on the remixed loader a long and a short blade
thingiverse
Strap holder for my neu DJI RC. ...I needed the option to attach the straps on the left and right of the DJI RC.
thingiverse
2 Bladed spinner. The standard size is 50mm but can be scaled up or down to the user's requirements. ... Requires 2 self-tapping screws as would be for any spinner.
thingiverse
3-Bladed Spinner designed for the Tony Nijhuis 72" Lancaster Kit. ... Requires 3 self-tapping screws as expected.
thingiverse
I had to find my helicopter blade CG, and my old way of propping up a credit card seemed silly now I have a 3d printer! ... I have up to 500 heli's here so it is 55mm wide.
thingiverse
Print your own landing gear for 150S ( and 180 but not sure) Blade RC Helis. Works well in PLA. ... Use cyano to glue parts together.
cults3d
... I designed this using parametric modeling in Fusion 360, so if you need one with custom sizes, I can easily re-mix it for your helicopter. Blade, T-REX, HIROBO, E-FLITE Please consider leaving a TIP for my time designing and testing this model.
thingiverse
The tail boom is 21mm in diameter and the main blades are 9mm thick by 55mm wide. I printed it using Filamentum 98A FlexFill. I designed this using parametric modeling in Fusion 360, so if you need one with custom sizes, I can easily re-mix it...