blink hound 3d models

This is a Blink sync module 2 Mount for a UK style power plug. The design uses the usb cable to hold the module in place. The excess cable wraps around the unit to keep it tidy. ...If you use a usb drive for local storage a SanDisk ultra fit works with...

This is a flagpole mount for the new Blink Outdoor Camera (Gen4). It was designed for a 2" diameter flagpole. The channel is large enough for an automotive hose clamp. Edit: Added a 3" and 4" pole mount file. ... Edit: Added hollowed models for resin...

Buddy randomly uses a blink doorbell to spy on his printer so I added a wedge mount for his doorbell onto the tool holder (not sure who to attribute the tool holder to because he just sent me the STL). ...Works great.

This is an Ender 2 Camera mount for the Blink 2 mini. Printed with 20% infil (cubic)80mm/s on an ender 2.takes about 4 and half hours on ender 2 to print.the Nut is a square rack mount nut,  and the bolt is the accompanying bolt.

I replaced my Ring doorbell with Blink, so i needed a topper replacement as well for it. it's for a 48-50mm pole. since doorbell is battery powered only it is easy enough to take off pole. i use a 2 inch 3/8" ubolt. ...special nut and tool included.

just a simple support for a blink camera and its flexible arm to be inserted on the top of a 12mm square grille. use double sided tape (optional) and a screw to fix the camera 'arm' to the support. ... then put the support on the top of a 12x12...

I replaced my Ring doorbell with Blink, so i needed a topper replacement as well for it. it's for a 48-50mm pole. since doorbell is battery powered only it is easy enough to take off pole. i use a 2 inch 3/8" ubolt. ...special nut and tool included.

... let's give him some surface-to-air capabilities to take down those pesky Decepticon flyers. The S.A.M launcher is mounted on Hound's back, always on the ready to take out any potential targets, and can be attached in both robot and alternate modes.

Bracket for ratchet straps, universal for curves, flat, or edges. Blink outdoors X2 ball head bracket with rain protection. Simply, take the rain protection off and take out the camera to change the battery. To be needed: 1x M4X10-15 mm for the ball...

The Blink Weavers are the first instalment of my new line of Eggresites - Feral Space Elves, that are using biotechnology and...ahem...magick to survive in the grim darkness of the warlike future. The Blink Weaver kit would be available on my...

Wall mount for the new Blink Sync Module 2 thank came with my Blink XT2 Outdoor camera - the port locations a little different than version 1 and the power supply is smaller. Left enough space to plug in a bigger USB charger and key as well as gives...

The inclination is set at 32° for the "Blink Edition". More options are coming soon! Recommended material: Ninjaflex Infill: 100% Print on one side with active support. This project is still a work in progress, so keep testing new things. If you...

The Blink Weavers are the first instalment of my new line of Eggresites - Feral Space Elves, that are using biotechnology and...ahem...magick to survive in the grim darkness of the warlike future. The Blink Weaver kit would be available on my...

... instructions: You need to remove the two transparent bezels and the back cover from the camera before putting it in the case. Tinkercad source: https://www.tinkercad.com/things/2k4Wgsu2vhY-blink-camera-bcm00100u-original-white-model-outdoor-case

Manufacturer: Stellar Works Collection: Blink Model: Sofa One Seater 696x800xH820 mm. Seat height 430 mm. Polys: 210,829 Verts: 210,782 On the model the Unwrap UVW modifier is applied Who works in V-Ray version lower than 3.1 be aware, in materials...

Manufacturer: Stellar Works Collection: Blink Model: Sofa Two Seater 1620x800xH820 mm. Seat height 430 mm. Polys: 1,051,757 Verts: 1,051,858 On the model the Unwrap UVW modifier is applied Who works in the V-Ray version lower than 3.1 be careful, in...

Blink outdoors X2 ball head bracket with rain protection. Simply, take the rain protection off and take out the camera to change the battery. To be needed: 1x M4X10-15 mm for the ball head Alternatively, 3.5-4 mm x10-15 mm in diameter. 2x...

Manufacturer: Stellar Works Collection: Blink Model: Sofa Three Seater 2320x800xH820 mm. Seat height 430 mm. On this model, the Unwrap UVW modifier has been applied. If you are working with a V-Ray version lower than 3.1, be aware that in materials...

Blink outdoors X2 ball head bracket with rain protection. Simply, take the rain protection off and take out the camera to change the battery. To be needed: 1x M4X10-15 mm for the ball head Alternatively, 3.5-4 mm x10-15 mm in diameter. ... 2x m3x20mm...

Remix and combine https://www.thingiverse.com/thing:2851232 and https://www.thingiverse.com/thing:3137935 After I installed solar panel for Blink XT2, the original mount doesn't fit when there's USB cable at the bottom. I needed to use a mount that...

A platform to lift the Blink Mini video camera enough to see over most (British) window frames, so you can sit the cam on the window sill. Designed to be printed on its side with NO SUPPORTS. Cable can be routed through the stand in various ways,...

Parametric creator for Blink camera hubs that can be mounted on holders or mounts, allowing users to create either a desk stand or wall mount. In SCAD settings, options are available to include mounting holes (for both types) or end stops for the...

This set contains: Blood Hound A, B, and C 25mm Round Base The model was supported on Lychee Slicer mango3d.io/downloads All files come pre-supported and include Lychee files. Using these files you can tweak the supports to your settings. The test...

The S.A.M launcher is mounted on Hound's back, always ready to strike potential targets, and can be attached to Hound in both his robot mode or alternate modes. --- This model may not be shared or sold in any way and is intended for personal use...

Its detailed specifications include 503,373 polygons and 500,582 vertices, ensuring an ultra-realistic representation of a Basset Hound dog head. Explore more unique designs like this one by visiting the 'Design3Dm' link on the right. ...We appreciate...

Designed an outlet mount for the Blink Sync Module 2 that allows for two different types of cable management options, cable wraps and cable tie anchor. The module and usb power plug fits snug and allows access to both usb and power ports, and access...

HeyhoI recently bought a Blink Mini Webcam to be able to track my 3D printer in the dark.Unfortunately, most of the existing mounts were ugly or impractical for my problem.So here is my quick solution. I fixed the weight to the floor with...

This is a Blink Mini mount for Kobra Max. It is a modified, taller version of the one I created for the Ender 3 V2. This will fit many printers, but the height was specifically made for Kobra Max. Print in upright orientation with support. I used...

Based on the Blink XT2 Power Bracket by Walchek (great design by the way). I opted for a different approach, designing two side brackets to attach securely to a wall or cupboard using screws or sticky-backed velcro. You can also use double-sided tape...

Based on the Blink XT2 Power Bracket by Walchek (great design by the way).Instead of hanging the sync module off a wall socket I just designed two side brackets to mount to a wall or cupboard using screws or a piece of sticky backed velcro (you can...