blink mini camera mount 3d models

I'm designing an advanced deck and FPV camera mount system with a rotating turret. This version 2 of my design enables easy installation - simply insert the turret into the deck slots, rotate it to position, then attach the servo from below for...

Mini keychain with photo camera design Can be used with lithophany or photo with dimensions of 21mm x 29mm. In case of making lithophane the dimensions of the lithophane should be. ... 31mm x 24mm x 2.8mm Page to make your lithophanes...

I crafted a small camera jib as a DIY project.

Position yourself to support a first-person view miniature camera.

Originally I was dissatisfied with how my X axis camera mount was fairly loose on the motor, while printing some cool motor visualizers I found that Clement's mount for the Hypnotic Extruder Visualizer was considerably more stable. ...So I jammed the...

Please refer to the github: https://github.com/joehou45/Amb82-Mini

Remixed Components -Raspberry Pi 3B+ case (versions 3, 2 & B+ also fit) designed by dktosoch - available on https://www.thingiverse.com/thing:2844013 -MP Select Mini GoPro mount created by 79DieselRabbit - accessible at...

Case for Adafruit 8x8 RGB LED display and the 8x8 Thermal camera chip

A Customized Camera Mount for the Mini Pan Tilt Module, Available from Adafruit and Pimoroni. The Mini Pan Tilt Module, sourced from popular retailers like Adafruit and Pimoroni, comes equipped with a standard Raspi camera. However, I aimed to...

Eachine TX01 TX02 FPV camera mount for Myosho Mini-Z Monster. To make the print without much support the ears are flat. You will need to apply a little bit of heat and bend them into shape. This support is not made to keep the car body with the...

Small polaroid camera in two parts to mix & match colours. The Camera Box require support but the Front Panel don't. I'm new to 3D printing and modeling so feedbacks are more than welcome! ...:)  

This is a camera lens setup for crafts and fun. ...Can be adjusted to whatever size you would like.

Commonly seen 15cm cable is not enough if the camera is mounted on Xmotor, since a high Z position will disconnect the camera. I am inspired by the ball joint camera mount from Prusa Mini Printbed Camera Mount with Cable Chain by darken. So I...

"Prusa Mini and Mini+ Cable Chains (x-axis motor, heatbed)" by Subtle3d: https://www.printables.com/model/27742-prusa-mini-and-mini-cable-chains-x-axis-motor-heat "Prusa mini Z Support with Cable Chain" by ShadowOfKlon:...

This is based on the original by @gjpc but smaller on the outside and (0.1mm) bigger on the inside, to fit my Mini.  This  reduces the thickness of the print to 1.0mm from 1.5, which sort-of works with my iPad case.  Since I did it up from scratch,...

The original design is for the Blink XT camera, and it's a really great design that shines. But the white indoor camera takes it up a notch with its sleeker profile - it's slightly thinner than the others. ...To fit them all in, I had to shrink it down...

Take the camera holder from your selfie stick and repurpose it as a convenient tabletop phone and camera stand. ...Simply reuse the existing screw, and then add an M4 nut along with a short M3 screw that's roughly 10mm in length to secure everything...

Wanted to add a camera to monitor my prints but did not want a bulky camera and also wanted it attached to the print head so you see the nozzle at all times. Print instructionsPrint is very simple. I have support structures enabled for these. you...

I don't have the camera model number handy at the moment and they're all different models that change every 15 minutes but it fits my camera perfectly, your mileage may vary. The fit of the curve against the fuselage depends on your plane, course, so...

Simple tripod with feet. ... Use with normal tripod screw or https://www.thingiverse.com/thing:595837 Designed for Raspberry Pi HQ Camera Module: https://www.thingiverse.com/thing:5820318

I'm currently working on a detailed 3D model of a compact drone equipped with a high-resolution camera. ...While the design isn't yet flawless, I'm continuously refining my modeling techniques and skills to achieve perfection.

1.0 MP CMOS WDR Mini Network Camera0.028 lux @ (f/2.0,A GC on), 0 lux with IR<br> 1280 × 720 2.8 mm @ f/2.0, Angle of view: 67.3° H.264/MJPEG 60 Hz: 30 fps (1280 x 720), 30 fps (704 x 576), 30 fps (640 x 480) 12 VDC ± 10%

1.0 MP CMOS WDR Mini Network Camera0.028 lux @ (f/2.0,A GC on), 0 lux with IR 1280 × 720 2.8 mm @ f/2.0, Angle of view: 67.3° H.264/MJPEG 60 Hz: 30 fps (1280 x 720), 30 fps (704 x 576), 30 fps (640 x 480) 12 VDC ± 10%

I'm seeking a compact, portable tripod suitable for my Gear 360 camera. To create it, I printed the design using my upgradable Markforged Mark One 3D printer, which now features the Olsson Ruby nozzle, allowing me to work with Matterhackers Carbon...

Human: Modified from ["LulzBot Mini bed USB camera mount" by sabi](https://www.thingiverse.com/thing:1582302) to support the [V2.1 extruder toolhead from Lulzbot](https://www.lulzbot.com/store/tool-heads/lulzbot-mini-single-extruder-tool-head-v2_1).

... 22.2mm wide cameras from RunCam. ...Specifically, it's designed to fit the RunCam Swift Mini and the newly released RunCam Split perfectly. ...You can see this mount in action with the RunCam Split at https://www.youtube.com/watch?v=6n1m9Ng2yMM.

The design of a simple seat for the HS1177 FPV camera fits perfectly within the Deformation Insect 130mm frame, providing excellent upward tilt. Three versions are available - 15 degrees, 20 degrees, and 25 degrees. Surprisingly, this setup also...

I've been itching to create a timelapse video of my Da Vinci Mini, but I knew I needed something smaller than the tripod I already have in order to get up close. That's when this idea popped into my head, and now I'm excited to see if it'll work. If...

I was determined to create a timelapse video of my Da Vinci Mini, so I needed a new tripod that could get up close. My current tripod is too bulky and wouldn't fit the bill, so I came up with an innovative idea that might just work. I'm eager to hear...

This is a neat little riser to be able to use the Prusa Mini Raspberry Pi Camera Mount from Seabird HH and the great and highly compact Prusa MINI Raspberry Pi Case from Joe. Normally these two parts cannot be placed besides each other. Even...