blink xt2 soffit mount 3d models

Mount Sinabung is a formidable stratovolcano located in North Sumatra, Indonesia. Created from 1 arcsecond resolution SRTM data extracted from the Space Shuttle, this precise representation encompasses approximately 0.6 million polygons. This...

A crucial step involves using sticky tape on both the OSD and case to create a sturdy mount. When it comes to printing settings, attention to detail is key. Start by selecting your printer model, specifically The Micro, which will enable precise...

I used 3mm carbon-fiber rods.Fill the gyroid innards with epoxy and allow it to dry.DurabilityI've had this mounted on my house for the last four months with no trouble. But an earlier version, without the inner epoxy, broke apart in a windstorm...

I have built this part previously, so I know it will fit seamlessly within the printer, and you can easily swap out the extruder motor (or any other NEMA17 motor) for mounting purposes. Unfortunately, I haven't installed a chuck or bit on my motor...

Found that the connection point can be a bit delicate and prone to breaking if overtightened, so to avoid wasting time reprinting the mount, I added a spare cap as a precaution. It's worth printing one or two extra caps to keep on hand in case of an...

This is a basic mount for attaching accessories to the Patton Robotics OneBot. All of the holes are unscrewed, so you will need screws and nuts to assemble it. I used 4-40 sized screws. You can watch my project summary video here...

This is a battery mount for this type of battery pack: https://www.amazon.com/Duratrax-5000mAh-Battery-Standard-Connector/dp/B004AF88K0/ It offers a snug fit for both the battery and the cover, with the cover snapping into place with a firm push due...

To secure the thermistor in the mount, a 3mm socket head machine screw can be used to clamp down on the cartridge tightly. Please take care not to overtighten the screw or damage the thermistor. I included the .STEP files just in case anyone wants...

... single layer will be filled with plastic, giving you a strong and durable part. You don't need to worry about rafts or supports for this print job. The LED light is designed to fit snugly into the mount, so it won't move around during printing.

I needed a cheap solution to mount my beamer. I decided to use Clamps. The beamer has moving parts and the resonances transmit to the clamped part. I didn't count for that, my bed is resonating the beamer fan which is unfortunate but I learned...

Each features a single screw mount. My print settings were optimized at 40 for inner walls, 100 for infill and 60 for print speed. A 30% infill geometric pattern was used, while the print material was red ABS. The 80 degree print bed temperature was...

I figured it was high time to create a semi-proper mount for it that would allow me to easily slip it on and off when needed, while also tidying up the wiring. The laser itself is one of these models: https://www.ebay.co.uk/itm/372496515390 The...

This is a mount for the SkySolve plate solving camera. It give fine control to azimuth and altitude settings. See skysolve thing here https://www.thingiverse.com/thing:4920959. This uses 2 2-56 screws and nuts to latch the altitude bearing in...

https://youtu.be/gM4oK52amfU Mount for your caliper! I am using some double sided tape to hold it, but i added a version with holes in case. I made it for my iGaging OriginCal. HOWEVER, i believe it should fit any caliper out there! Supports...

This is a basic helmet mount that I designed for my Mk3 iron man helmet. The part is in two pieces that can be printed with minimal support material. I sliced up my design and printed it on my Ender 3. There are no tolerances for this design, so...

The original side "wings" which serve as rubber holders of the original attachment, do not have to be removed. Matching holder on the bike saddle:https://www.prusaprinters.org/prints/62342-gopro-like-mount-for-bike-saddleIf the nut in the linked...

I made this mount for my telescope to take pictures of the eclipse, and the results are amazing! Shot with a small kit telescope, with a magnification of 35x, I was even able to see sunspots. Here's a timelapse of the eclipse through my phone <a...

... Mounting_Bolt_Size is specified at 3.2 mm. Support_Height is set to 5. Standoff_Height is also set to 6. Cable_Tie_Width is defined as 4 mm. Standoff_Matrix is set to [[-15, -15], [-15, 15], [15, -15], [15, 15]]. Custom_Standoff_Height is set to 6.

... The orange fiberglass rods used in gardens to mark ditches and other features are typically around 8mm and use the larger sprinkler mount. ... This setup is surprisingly simple yet incredibly sturdy and useful if you have the same sprinkler system.

I built this mount specifically for my telescope to capture stunning images of the eclipse. Paired with a compact kit telescope offering 35x magnification, I was even able to spot sunspots in incredible detail. Check out this timelapse of the eclipse...

I just made an economic model of the Shoe support (wall mount) by andy25lion (https://www.thingiverse.com/thing:3705605) It uses less material and less time to print.The infill needs to be at least 20%.37.5% Less PLA and in my printer about one hour...

This multimeter mount was designed specifically for an AstroAI DM6000AR. However if might work for other multimeters as i have not...

Mount for your caliper! I am using some double sided tape to hold it, but i added a version with holes in case.</p><figure class="media"><oembed url="https://youtu.be/gM4oK52amfU"></oembed></figure><p>I made it for my iGaging OriginCal. HOWEVER, i...

...I mounted the bracket that came with the extinguisher to my brackets with a couple #10 screws and nuts and I put it in place after arriving at the show. After the show I stow it in the trunk. Please Note! This is temporary and just for the car show.

A simple wall mount for a small Remington Hairdryer, with a hole for a hairbrush and a slot for a small comb. Fixed with 2 screws, although there are 4 holes if you think you need more. Saves some space in the bathroom and is surprisingly sturdy....

Originally designed as a variant of the Paxtruder, this model features an added mount. The acrylic components are specifically created with "no stress" in mind and are made from 5mm cast acrylic, accompanied by a 1mm spacer plate. To minimize stress...

A Paw-some Monument: A Canine Tribute to Mount Rushmore. This 3D print masterpiece is designed for the Ultimaker 2 or 3, allowing it to be printed without supports at its current size. In Tinkercad, several modifications were made: * Dog models...

... an adjustable angle version. 10/13/17 - A new model has been uploaded, this one is a more precise shell design that fits better. Unfortunately, the cam sticks out slightly below the mount by about 1mm, which will be addressed in a later update.

Hi there!Thank you for downloading my camera mount for 3D printers.About the model:This camera mount is designed to attach a webcam to the 40-2020 extrusion commonly used for 3D printers. You can adjust the position by loosening the M3 screws of the...

Thing Title : Master Key Keeper Thing URL : http://www.thingiverse.com/thing:12989 Thing Author : John Biehler Thing Licence : Creative Commons - Share, Adapt and Attribute [1] Thing Title : Solar Spool Cable Organizer [1] Thing URL :...