bltouch anycubic 3d models

... any E3D setup but welcome feedback or questions. Print settings: Printer: D-Bot Rafts: No Supports: No Resolution: 0.3mm Infill: 25% Notes: Printing one of each shim requires minimal filament and enables fine-tuning for the optimal BLTouch height.

... RC6) to bitbucket for CL260 + BLTouch + Full Graphic LCD. https://bitbucket.org/effebal/cl260-bltouch-version-marlin-1.1.0-rc6 If you want to use this firmware with the original LCD, you'll need to modify the lcd section in the configuration.h file.

BLTouch Mount for JG Aurora A5: You'll need Screws M3 with a 15mm thread, one for standard fan ducts and one for the JG MKII duct. I used this calibration tool to set up the height: https://www.thingiverse.com/thing:2263497. My settings for...

Original BLtouch mount for ER20 printer. One version requires a change in one of the screws that holds the fan cage, the other doesn't require this(it has a pocket for it to slide), but i haven't tested if tolerances are ok because I had a spare...

Human: Custom fan mount for Anet A6 featuring BLTouch sensor integration and X-axis cable chain attachment. All required chain components can be sourced from the original design on thingiverse.com/thing:2168268. This modification allows for full...

PLUS: - cable cover - bltouch/3dtouch spacer if you need correction - Offset: X-51 Y-12 Really important -> check the bridge orientation ! ...See photos for better understanding FORE MORE INFO CHECK MY IG CHANNEL -->...

This is a remix of the capacitive proximity sensor mount into a BLTouch mount. It should hold the sensor (not including the pin) 8.3 mm above the print bed when the nozzle is on the bed. ...In your Marlin config, start with NOZZLE_TO_PROBE_OFFSET set to...

With a thin spacer it gives the perfect amount of space to hide the BLTouch between the main Cover and the mount, giving it extra style points ^^ **What you need and most likely can't print:** 4x M3 Nuts 2x M3 x 22mm Screws (I took 25mm and cut them...

Annoying, but what can ya do? This thing uses brass threaded inserts so the bltouch can be attached, if you want through-hole, feel free to remix. Print Settings Notes: I recommend a lot of perimeters so that when you melt in the threaded insert it...

I couldn't find a bltouch bracket for my matrix extruder that was on its own. So I made this one, the previous one I tried had to much movement. This one seems to work very well for my setup. I printed it in petg, with painted on supports where...

I bought an extension cord for my BlTouch and the connector wouldn't fit through the original version's hole... I printed with 3DOnline's Precision PLA 1.75mm 500g Violet Translucent filament:...

This is a remixed, slimmed down version of the MinionD BLTouch mount. It's approximately 33% lighter than the original, weighing in at 4 grams. The reduced size helps minimise interference with after market ducts. I slimmed this down to minimise...

move down the last 2mm) I also have a "deployprobe.g" which reads: M280 P3 S160 I1 ; Reset the probe in case it has faulted G4 P450 ; Wait 450ms for probe to reset M280 P3 S10 I1 ; Deploy probe G4 P75 ; Wait 75ms and a "retractprobe.g" which reads:...

Used the part that the BLTouch mounts to and changed it to mount on the side of the carriage instead of in front. It mounts using the 2 bolts for the linear bearings carriage. I used 40mm bolts for my setup YMMV There are 2 versions. For me...

Improvement: -Mesh invalid -Extruder error -PID fail -UBL error Installation instructions in the .rar Link to the Bltouch binding used for firmware V1-1.2. ... https://www.thingiverse.com/thing:4560281 UPDATE 27/11/2020: Genius+firmware+Blt...

It's a smart move to check if your BLTouch is working evenly across the entire bed. Designed specifically for Tevo Flash, but it will also work great with Ender-3 too! The squares are connected, but just barely. Print on a clean surface and use...

There are instructions on how to get a BLTouch working with the Anet A8 here (http://www.thingiverse.com/thing:2091529) and they should work with the A2 as well with minor changes, however I have not attempted this as I've opted to completely swap...

This part is designed to mount a BLTouch z-probe to the two M3 threaded holes found on the left side of the Flexion extruder coldbar. It minimizes the already large x-offset from the primary nozzle to the probe tip and properly positions the probe in...

When I switched to a BLTouch Probe, I realized there wasn't any straightforward probe mounts available for the FT5. At that point, I decided to cut one from aluminum, but I understand that it would be very easy to create a mount for others to use. It...

It secures the BlTouch between the wheels of the X-Carriage, allowing for automatic probing of the entire bed. Initially, I used a 5mm offset without a shield and encountered overheating problems. This led me to discover another mount (listed...

When I converted to a BLTouch Probe, I noticed there wasn't any simple probe mounts available for the FT5. At the time, I chose to cut one from aluminum, but I realize that it would be very easy to make a mount for others to use. So... here it is! It...

Upon testing the gap with with this alignment spacer (https://www.thingiverse.com/thing:2267858/), I found I needed to raise the BLTouch by 1 mm. I figured the best way to do that was to take a section of the mount I was already using and create a...

Buy filaments here ---> https://eryone3d.com/?ref=promoWorldwide shipment (3 days)15% COUPON -->3DCREATIONThis is a remix of Satsana fun duct optimized for use with stock fans.UPDATE -->VERSION v2 WITH MORE SPACE FOR X ENDSTOPMain benefits...

A very simple mount for a BLTouch, or clone, probe for the flyingbear reborn. The fit is pretty tight, but I aimed to avoid all possible collisions with the stepper motors and the belts, this iteration should solve all the collision problems. You...

This is a "new" Hemera ADXL345 BLTouch 5015 fan duct for all of you who are got an E3D Hemera. It has not been tested as I do not own a Hemera myself, designed it for a friend, but it is got everything that I have learnt about 3D print cooling and it...

Upon testing the gap using this alignment spacer (https://www.thingiverse.com/thing:2267858/), I determined that I needed to raise the BLTouch by 1 mm. I decided that the best way to achieve this was to take a section of the mount I was already using...

... triangle lying flat on the bed and the mount "shelf" pointing upwards in the Z-direction. I used M3 bolts and nuts, adding some between the BLTouch and the mount to space it correctly relative to the nozzle according to the manual (2.3 to 4.4 mm).

... wrestling with stubborn globules of hardened resin in your tank with a scraper? ... Look no further! Introducing the Anycubic Rake, expertly printed on my trusty Anycubic Photon specifically designed for seamless integration with my Anycubic Photon.

Auto mesh bed leveling has been added using the BLTouch with this mount: https://www.thingiverse.com/thing:2815399. Thanks to Robscar for helping me get it done and for the mount. The stock extruder will now extrude 100mm no more over/under...

I couldn't find a bltouch bracket for my matrix extruder that was on its own. So I made this one, the previous one I tried had to much movement. This one seems to work very well for my setup. I printed it in petg, with painted on supports where the...