bltouch anycubic 3d models

Tiny and simple BLTouch mount for the CR10S Pro Mine is installed on a CR10S Pro v1

Mount to fix BLTouch to OEM fixing points on a Tronxy XY2 Pro I should add, as I have had a lot of questions on how I got the BLTouch to work, I did not use the original Chitu board, I changed to a SKRv1.4 Turbo that has pre assigned plugs for the...

... the dragon rear toolhead mount. ...Untested heights of the bltouch to the nozzle etc. Based on beta2 part from the official stealthburner STLs. Probably have to shim the bltouch just a little with some washers. ...This probably has to be ABS only part

[BLTouch Cover V2.1](https://www.thingiverse.com/thing:4634422) --- Version 2 of my Other BLTouch Remix comes with just a few adjustments. There are four variations to choose from, and you'll have to figure out which one works best for you based on...

... For official resellers, refer to the following links: CANADA : http://store.timeshell.ca/BLTouch?tracking=57c893bc85620 GERMANY : http://www.filafarm.de/ To purchase a TEVO Tarantula 3D printer, visit https://tevo3dprinterstore.com.

Place a support under the BLtouch screw mount, positioning springs between the BLtouch and main bracket for optimal alignment. Thread screws through holes in the support and then through the springs into the nuts tightly. ...With this setup, the height...

Modified Woody's architecture to mount the BLTouch directly above the print bed during the homing sequence, incorporating a central opening for effortless sensor realignment.

Super-simple mount for the BLTouch probe on the Eryone Thinker SE printer. ...I tried other mounts but none of the others fit properly.

I just need the BLTouch mount from Thingiverse, specifically thing 4076966, modified with a pre-drilled hole for easy access to the adjustment screw.

This is the customized slider from the BLTouch adjustable mount crafted by LSmotion, tailored specifically for the Piper 2 3D printer designed by Piper3D.

This is a bltouch mount for Kingroon kp3s new Titan Extruder set. ... i use 2x m3_4 2x m3_6 2x m3_washer

Fixed daniels (https://www.thingiverse.com/danielis) BLtouch adapter (https://www.thingiverse.com/thing:4843403) for the BIQU B1. Adjusted so it fits the bolt on the gantry. ...

Install the BLTouch mount on your Creality Ender 5 - a straightforward process, and one I've found to be more accommodating than similar designs found on Thingiverse.

BLTouch Mount specifically designed for the Wanhao D6 3D printer, mounts securely over the heatbreak fan. ...Requires printing upside down to ensure a snug fit.

Yet another BLTouch mount for Creality CR10s Pro, with stock nozzle/hotend. ... Designed to be sturdy so that it won't warp over time if printed in PLA.

If you have a custom printer with the MK3S/S+ extruder, this design will be handy if you prefer the BLTouch probe.I recommend that you mount your BLTouch to the part before attaching it to your extruder.If you are curious, my MK3S+ extruder has a...

bltouch mount bracket for Sidewinder X1. Mounts behind fan. Will need slightly longer bolts, 2x M3 x 20 works for me.Probe offsets:X: 24Y: -29Z: -3.2

This mod is a simplified version of: https://www.thingiverse.com/thing:2763931 It's been made more assemble-friendly. ...The BLTouch mount has been secured in place.

A remix of the original where the fan is moved. ...I just added the hole for the z-cable / bltouch cable that was missing.

Hi, This is a dedicated support for BLTouch or Touch ID, leveraging the standard setup for the Diamond Hot End. ...Install this component atop the Diamond Fan.

... The red wire should be connected to the +5V power pin on the board, while the black wire should be connected to the GND pin. Finally, plug the BLTouch probe into the MendelMax 2's controller and configure the settings in your slicing software.

Added relief grooves for easy screw installation. ...Designed a straightforward BLTouch mounting system compatible with 30MM fans, utilizing M3 hardware throughout.

My first shot at building a BLTouch mount, and I'm excited to put it through its paces once I've got it printed and installed!

The user utilized the cap from the Anet A8 E3D V6 carriage, sourced from TNS, and integrated the BLTouch mount designed by Rhuuk.

I mounted a bltouch sensor to my 3D printer's carriage. ...It perfectly matches the design of this carriage: https://www.thingiverse.com/thing:2658012.

##################################################################### # Probe ##################################################################### #[probe] ## This probe is not used for Z height, only Quad Gantry Leveling ## In Z+ position ## If...

I'm using the U1JO Hemera fan duct and BLTouch. ...However, I needed a single BLTouch mount to locate a single probe in front of the extruder fan. ...So I did a crude chop job of the original dual mount plate.

To create a simple upgrade, a BLTouch mount is added to the existing v3 carrier plate. This process involves precise measurements to ensure accurate positioning of the components. ... The offsets I measured are as follows: X-axis offset: 45 units,...

I won't provide instructions on how to install the BLTOUCH on the 4MAX Pro because Thingiverse's frustrating interface is just too annoying with their constant interference. Sorry about that. ... This enclosure secures the cables of your in-printhead...

I wanted to use this BLTouch cover for thing 4637453 but had to make some adjustments due to the BLTouch Cable being on the outer side. ...I also added little clips so there is no need to worry about the print weakening over time and falling off.