bltouch ender 3 3d models

Added a provision for securing cables with 2 cable ties on to the Satsana body

I created a concise and straightforward guide on how to get ABL running with BLTouch or 3DTouch without cutting the display cable on the Ender 3, also avoiding the pin 27 board since it's nowhere to be found. ... The guide is presented in picture format...

When I upgraded my Ender-3 to direct drive I decided to buy an aluminum stepper mount, but it was too big to work with this Satsana Fan Duct. Using a little bit of magic I was able to make this work and here it is for anyone else who wants a fan duct...

This is a remix of https://www.thingiverse.com/thing:4682779 with the joint between the Red Squirrel and BLTouch mount cleaned up and a modified base lock. you can find the fan guards and clamp with the original here:...

My Ender 3 is using the Creality Direct Drive so I Remixed https://www.thingiverse.com/thing:4697079 to suit those needs. Things I changed: Shaved a little off the top plate to make room for the motor Removed the wasted space under the front...

My Ender 3 is using the Creality Direct Drive so I Remixed https://www.thingiverse.com/thing:4697079 to suit those needs. Things I changed: Shaved a little off the top plate to make room for the motor Removed the wasted space under the front fan...

Why we can't upload as a 3mf is beyond me :-D This is a remix of an Ender3 mounting plate for the Voron print head. There are several available here on thingiverse but I couldn't find any that had BL-Touch and ADXL345 mounts with threaded...

I couldn't install my BLTouch on Ender 3 after watching tutorials on YouTube or searching forums online. I gathered all the information and errors I found and modified the firmware. This guide is for people using Petsfang with stock hotend and 5015...

I create this support to adapt my BLtouch in Sprite Pro Ender 3 I just use 4 M3 x 15 bolts and 2 nuts

Fits the BLTouch and 3DTouch for Ender 3 or Ender 3 PRO Special features -The Extruder Fan Cover can be removed independently (no need to also remove the BLTouch mount), thus not messing up the probe Z offset -Optimized cable placement. -Small and...

The holes were aligned and sized using the f3d model of the Ender 3 provided by Creality.Offsets are [X:-43.6, Y: -5.8]. ...My Z offset is -2.4, but you should calibrate yours.Layer Height0.2 mmInfill20% GyroidSupportsBLTouchMount.stl - no supports...

... 3, and this one was a bit too short, so I modified it using meshmixer. ...This modification has been working perfectly on my Ender 3 for about two months now! ...Printing at approximately forty percent infill with PET-G at a layer height of point two.

Perfectly straightforward design for mounting the BlTouch Sensor on an Ender 3D printer bracket. The probe is situated directly to the left of the extruder. Marlin's Z_Offset settings are: x at -40, y at -10, with a minor adjustment possibly required...

Update (2020-06-26): Updated STL file.\r\n\r\nThis remix brings together the innovative nut-less design and recessed mounting points from **adj-bltouch-mount-3D-mount-EC-mod.stl** and **adj-bltouch-mount-ec-mod.stl**, while fortifying the carriage...

Cura profile for PLA+ (K6) 1.75 ↪Nozzle 0.4 ↪Layer Height 0.12 +Start/End GCodes for BLTouch Ender 3 (Ender 3 Pro) +STL file Cross ————————————————————————— Ultimaker Cura 4.11.0 ————————————————————————— Infill as well as support structure can vary...

Теперь можно легко и просто установить датчик автоуровня (BL-Touch, 3D Touch) к этому креплению при переходе на директ. ...Проверено на Ender 3 Pro

... of the BLTouch specification. The mount can be attached to the hotend via the original Ender 3 Fan case screws. To attach the probe to the mount 2 M3 screws and nuts are required. ... **Probe offsets:** x: -44.5mm y: -05.3mm

This allows you to attach the Bondtech LGX-FF extruder to your Ender 3-Pro. It also allows the use of a BLTouch. I used the fan duct & mount from here: https://www.thingiverse.com/thing:4746610. Make sure they get credit for that. I updated...

Pre-oriented for printing, prints with supports no additional hardware needed except the screws that came with your BLTouch

A remix of the original where the fan is moved. ...I just added the hole for the z-cable / bltouch cable that was missing.

My goal was to make it as simple as possible so that all the original parts can be used and a BLTouch can be mounted additionally. + Compatilbe with Unitak DirectDrive Kit for Ender3 / Ender3 Pro This design from user: eric-anastas is perfectly...

I modified the BLTouch cover and added this fan cover to create a new design. You can find more information about these modifications online, specifically on thingiverse.com, where you'll see references to designs like 3716291 and 2990894. ...Please be...

This is a strong BLTouch support for the Ender 3 Max. ... Here is the video about it: https://youtu.be/JQctHZLkdIU

G-Code included (Sliced for Ender 3 V2 use Cura) Remark: I am use this Gcode with octoprint and it might not work by sd card since it is Marlin-style Gcode. I have added Brim for better bed adhesion since ender3 v2 comes with glass bed. 2x...

Please give it a ❤️ if you like it 🥰This is a strong BLTouch support for the Ender 3 Max.Here is the video about it: Please give it a ❤️ if you like it 🥰

... the mount holes and mounted the BLTouch directly with a slightly larger set of screws. I used the install guide and firmware from Smith3D, which was super helpful: https://smith3d.com/ender-3-v2-bltouch-firmware-installation-guide-by-smith3d-com/

BLTouch support for Ender 3 V2, fits perfectly to your Ender 3 V2, does not require any screws other than the original one. To install it, simply unscrew the wheel from the printing carriage, insert the support, and screw everything back in, the...

A mount for a 3dtouch or bltouch bed leveling sensor that can be mounted on the two 3mm threaded holes of the Ender 3 v2. The sensor is attached to the mount with 2 additional 3mm bolts, which tap into 2.5mm holes. I'm using a Z-offset of -0.70mm...

... It securely clips onto the Ender 3 fan, providing a sturdy support mechanism for itself. To calibrate this setup, you'll need to adjust the X probe settings and Y probe settings within your firmware, specifically in the "configuration.h" tab.