bltouch mount geeetech 3d models

This is a sturdier mount with ribs to hold the BLTouch. Printed at 0.16 mm layer height with support. Set in firmware: Nozzle offset of -33, -11. ... Remixed from: https://www.thingiverse.com/thing:3980327

This is an innovative BLTouch/3DTouch auto bed leveling sensor holder designed specifically for the versatile carriage found here: https://www.thingiverse.com/thing:3910847. ...To successfully print this mount, I recommend printing it upside down with...

BLTouch mount designed to work seamlessly with Thingiverse's 2368133 model. ... I incorporated an additional spacer component, allowing users to adjust the Z-height as necessary by simply increasing or decreasing the part's dimensions.

BLTouch mount for Voxelab Aquila 3D printer. Printed using PLA material and tested with Klipper firmware. X/Y offsets are about -40mm/-10mm. Z offset is 2.05mm - measured during calibration. ...

This 3D printer offers a pair of BLtouch mounts compatible with the Black Widow model. ...The required STL files can be found at this Thingiverse link: http://www.thingiverse.com/thing:1950504

This is a new mount for the Voron wich replaces the standard probe PL-08N2 with a BLtouch. The BLtouch will fit in the same space as the probe PL-08N2 and be held in place by the beltclips. Print the two parts in ABS with 0.2mm layer, 4 outlines...

... for BLTouch, the front piece is still the same. IMPORTANT: I didn't try this mount cuz I'm constantly working on a project and I cannot take apart my printer right now. ...But if you have any improvements or fixes to suggest, please let me know

https://www.amazon.com/gp/product/B08V8MSWZM/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&th=1 I am not affiliated with this product in any shape or form Product arrived, no bltouch mount. Seller sent garbo file. I am better than that Open...

As an alternative, I adapted a fan mount that another user had previously posted online into a functional BLTouch sensor setup. Since I primarily print with ABS filament, I don't have the need for a part cooler attachment. ...By sharing this...

I removed the unnecessary components from "Geeetech Sensor and Fan by Hexit", specifically the fan section, as it's not required for my purposes.

I modified this remix from https://www.thingiverse.com/thing:2419702 to fit the 8mm frame of my GEEETech i3 Pro-B 3D printer.

This is a mount for the BLtouch for the Voron 2.4 The standard probe PL-08N2 have a max operating temperature of 70 degree Celcius and will eventually melt when printing ABS. The BLtouch can withstand a higher operating temperature and is more...

This is a revised design of axelsp's D-Bot Hotend clamp with BLTouch mount.\r\n\r\nIt was modified to position the BLTouch in front of the extruder, freeing up space for fans on either side of the extruder and positioning the sensor closer to the...

Printable part that enables mounting a Titan extruder, V6 Hotend and a BLTouch on your Cetus, making it easy to upgrade your 3D printer.\r\n\r\nFor added stability, use the support underneath the small lip at the base and the flange where the BLTouch...

... for a reliable SKR 1.3 and created this mount specifically for it. Thankfully, the 3dTouch (which isn't the original) fits perfectly, but if you're looking for a seamless upgrade, the authentic BLtouch will slide in without any issues whatsoever.

This is a remix of WillLyon's dual fan duct to add a BLtouch mount to the front of the extruder. You will need spacers, springs, or some other form of screw standoff to raise the BLTouch about 10-15mm to the correct level. ... [Check out my collection...

... hit the plate when the pin is up, or if you relocate it higher the nozzle will hit. I relocated the holes down 2mm on the mounting holes, and took 2 mm off the thickness of the part due to the screws that came with the bltouch were too short.

This mount uses the two threaded holes to attach the mount in place of the larger idler wheel mount screw. I believe they are m2.5x0.45 screws. ... I used the wiring guide and configuration/firmware found here:...

A versatile mounting solution for attaching a BLTouch probe to the head of your Wanhao Duplicator i3 or other similar printers like Monoprice Maker Select, Cocoon Create and more. ...This mount securely fastens onto the fan shroud, and can be used in...

BLTOUCH MOUNT FOR CREATIVITY ELF PRINTER, SETS Z OFFSET TO ABOUT -1.38 MM FROM BED. TO BE SAFE I WOULD SET IT A LITTLE HIGHER AND ADJUST AS NEEDED. HOLD THE MOUNT FIRMLY AGAINST THE METAL MOUNT WHILE TIGHTENING THE BOLT SO THERE ARE NO GAPS BETWEEN...

Then I tried to mount the BLtouch probe directly on this mount, nice and close to the extruder. But that left the height-difference between the nozzle-tip and the probe housing 2 millimeters shorter than recommended by AntClabs. So I mirrored the...

Needed to mount my BLtouch on the side of my printhead and the only mounting point is the 4010 blower fan. This mount will work on either side. You will likely need longer fan mount screws as this mounts in from of your blower fan. This should work...

I wanted for this mount to print easily while keeping the display absolutely rigid for encoder presses, at a 45 degree viewing angle, not to interfere with bed travel, and to allow easy access to the Y axis belt tensioning wingnut. This bracket...

... ...I really wanted to install a BLTouch on it, but none of the "official" creality mounting plates work with the tiny x-axis carriage. I couldn't find anything here on Thingiverse that could help, so I decided to model something myself. Here it is!

...I remixed it so that it activates the End switch and mounts the BLtouch as the Stock ender 3 mount would. ...Hope this helps someone out there as ive been at this for a few days trying to find something that'll work for me with the PrinterMods MDD..

... which looked ugly and caused rattling issues. This modification enlarges the mounting surface of the BLTouch mount so the M3x10 bolts fit perfectly without any play. ...Keep in mind that you will need to adjust your X offset in your firmware.

This is a remix of [einarms](https://www.thingiverse.com/einarms)'s [Bltouch Mount Hypercube Evolution](https://www.thingiverse.com/thing:2464991). The shank length has been extended and the sensor flange thickness reduced to allow more adjustment...

I decided to make this mount for the bltouch for this https://www.thingiverse.com/thing:4732947 cooler without making any holes but using the already existing one. ... I made this mount SUPPORTLESS so you can print it without those annoying supports or...

I ran low on White filament and didn't want to reprint my [Satsana Duct](https://www.thingiverse.com/thing:4623647), so I designed this extension to mount my BLTouch. ... I used a spare m3 bolt from the stock fan shroud to mount it.

Mix of two BLTouch mounts so the bracket attaches in front and behind the fan making for a much stronger and straighter mount. ...On my printer the offsets ended up being X=40, Y=0, Z=-1.41, though the Z should be measured per installation.