bltouch mount geeetech 3d models

Screws: -bltouch M3 max 14mm -mount M3 min 6mm Firmware compatible with board MKS Robin Nano V1.2 Pin servo PA8 BL Touch socket Firmware > 1.2 need "Initialize EEPROM" manually after flash Marlin 2.0 source: http://marlinfw.org/meta/download/ Based...

Hello makers, I decided to remix the CR-10 BLTouch mount by shocksofmighty because my original bltouch was not the right size and the nozzle scratched my bed. I'm sharing the "new" simple version with you now. v1.0 - Added some material to level...

... I used a ball mount to attach the camera afterwards. NOTE: This is just the bracket, it does not include the ball mount. I have attached the Fusion file, STEP, and STL. ... This should fit the A20M, and A10M, but I haven't tested the A10M.

The BLTouch should be mounted facing the right side and the cables should be pulled through the longhole in the bracket.You will need additional screws, nuts and washers for the mounting of bracket. The needed parts are mentioned...

This design utilizes the stock 30mm front heatbreak fan that came with the e3d kit, and a single 5015 blower fan to power the 200 degree cooling duct built into the front side of the mount. The back side features built-in cable management, making it...

It mounts with no need to unscrew or add any extra screws. ... ...

####GIRO.ETS - BLTouch Mount####\r\n####General####\r\nThis bracket is specifically designed to be mounted on top of the hotend enclosure, with the BLTouch positioned facing the right side and the cables carefully routed through the longhole in the...

With a thin spacer it gives the perfect amount of space to hide the BLTouch between the main Cover and the mount, giving it extra style points ^^ **What you need and most likely can't print:** 4x M3 Nuts 2x M3 x 22mm Screws (I took 25mm and cut them...

I created this mount which allows for adjusting the height. It uses the original hardware, so no extra parts needed. Printed on my Elegoo Mars 3, but should be FDM printable as well. I've been using this for several months without any issues. Works...

I also rotated to the proper printing orientation to save everyone a step. A simple mount for BLTouch (Smart) for the stock CR-10 setup. ...I've reclaimed pin 31 from the SD card to use for servo control.</p> <h3>Print instructions</h3><p>Licence:...

... area surrounding the M3 bolts requires longer bolts than what comes standard with the extruder, but these are common sizes. To ensure clearance in all orientations, I carefully positioned the BLTouch mount at a safe distance from the heat block.

I created this mount which allows for adjusting the height. It uses the original hardware, so no extra parts needed. Printed on my Elegoo Mars 3, but should be FDM printable as well. I've been using this for several months without any issues. Works...

Original BLtouch mount for ER20 printer.  One version requires a change in one of the screws that holds the fan cage, the other doesn't require this(it has a pocket for it to slide), but i haven't tested if tolerances are ok because I had a spare...

Used the part that the BLTouch mounts to and changed it to mount on the side of the carriage instead of in front. It mounts using the 2 bolts for the linear bearings carriage. I used 40mm bolts for my setup YMMV There are 2 versions. For me...

Simple BLTouch Sensor Mount for Anet A2 Printers. Compatible with Part Cooler (http://www.thingiverse.com/thing:2197963). Print at 20% infill since there shouldn't be any weight or stress on the mount other than the weight of the touch sensor...

The BLTouch mount I created replaces the fan in the rear and is compatible with various hotend setups. It's centered behind the nozzle, resulting in a Y offset of around 20mm in Marlin firmware. I've added photos and fully calibrated the system...

Visserie : - 2 x écrou M3 - 4 x vis M3x8mm - 2 rondelle M3 (option) C'est un remix de https://www.thingiverse.com/thing:4694182 ________________________________________________________________________ Offset Bl Touch mount. With this mount the BL...

A bracket stronger and a little longer than the original, to hold my chinese BLTouch clone on my A8 printer.

This is a remix of the capacitive proximity sensor mount into a BLTouch mount. It should hold the sensor (not including the pin) 8.3 mm above the print bed when the nozzle is on the bed. ...In your Marlin config, start with NOZZLE_TO_PROBE_OFFSET set to...

This part is designed to mount a BLTouch z-probe to the two M3 threaded holes found on the left side of the Flexion extruder coldbar. It minimizes the already large x-offset from the primary nozzle to the probe tip and properly positions the probe in...

* No plug is required to attach the cable to the mount; the cable can be soldered directly to the BLTouch. ... # My settings for Marlin Settings in _Configuration.h_ ``` #define X_PROBE_OFFSET_FROM_EXTRUDER -38 // X offset: left -right [of the nozzle]...

6/4/2019: syncing with latest bear dev version 6/3/2019: syncing with latest bear dev version 5/25/2019: syncing up the body with the latest bear dev version (bear_dev_bltouch_v6.stl), per Greg's notes this should improve hotend cooling around the...

The z-offset you'll have to figure out yourself. Warning The BLTouch mount might bump into your x-axis assembly on the left. ...Please double check that you have proper clearance.</p> <p>My X-axis switch is moved forward a bit because of <a...

... triangle lying flat on the bed and the mount "shelf" pointing upwards in the Z-direction. I used M3 bolts and nuts, adding some between the BLTouch and the mount to space it correctly relative to the nozzle according to the manual (2.3 to 4.4 mm).

This is a mount to allow a BLTouch to be used with an Ormerod printer. This object requires the Ormerod 2 E3D v^ Hotend Mount with Fan mount to be installed (https://www.thingiverse.com/thing:1005956). This object uses the fan mounting bracket on...

Human: Custom fan mount for Anet A6 featuring BLTouch sensor integration and X-axis cable chain attachment. All required chain components can be sourced from the original design on thingiverse.com/thing:2168268. This modification allows for full...

BLTouch Mount for JG Aurora A5: You'll need Screws M3 with a 15mm thread, one for standard fan ducts and one for the JG MKII duct. I used this calibration tool to set up the height: https://www.thingiverse.com/thing:2263497. My settings for...

This is a remixed, slimmed down version of the MinionD BLTouch mount. It's approximately 33% lighter than the original, weighing in at 4 grams. The reduced size helps minimise interference with after market ducts. I slimmed this down to minimise...

Original BLtouch mount for ER20 printer.&nbsp;One version requires a change in one of the screws that holds the fan cage, the other doesn't require this(it has a pocket for it to slide), but i haven't tested if tolerances are ok because I had a spare...

This is a hastily cobbled assembly to secure my BLTouch in the supplementary extruder location on the X axis of my MendelMax 3.