blue snowball arm 3d models
119394 3d models found related to blue snowball arm.thingiverse
This is a simple gadget to attach a Blue Snowball (or other) microphone to a standard "lamp arm" and it also includes a pop filter. The bird is not included :-) Arm_long.stl and ring_center.stl have to be glued together. I've included the part...
thingiverse
A small bracket for adapting the blue snowball onto the end of a swing arm lamp. Similar to This one on amazon. The Peg is slightly oversized, to allow the microphone to cut its own threads. A small bump is included on one side to help with rotation....
thingiverse
you might also have to tighten up the rest of the screws on the arm to support the extra weight of the mic. For the mic i used the original stand and took off the folding legs. just unscrew the screw on the very bottom of stand and take out the legs...
thingiverse
Tested on the LG 34um58/68, but I think it would fit on the other 34" LG Ultrawides as well. ... A screw into one of the lower VESA mount holes does the job, and doesn't block the monitor control knob.
thingiverse
a shorter stand for the blue snowball microphone, or softballs i'm not your mother.
thingiverse
Simple stand to replace my blue snowball mount (non-adjustable) after I accidentally dropped and broke the original one
thingiverse
A clamp and screw created to hold your blue snowball microphone. ...Prints in three different pieces designed to require no glue, all pieces should fit together snugly.
thingiverse
Remix of my original blue snowball mount, 2 Sizes small and large, Addeds some adjusta ability on hight. 6 x M4x8 required for hight adjustablity. ...
thingiverse
This is a pop filter I designed to work with a Blue Snowball microphone. I super glued part 1 into part 2. ...then stretched a knee high stocking over the hoop trimmed it up a bit and used a rubber band to cinch it up at the bottom.
myminifactory
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...
thingiverse
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball. I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. I used dynamic layer height in...
thingiverse
This is a pop-filter for the "Blue Snowball" microphone. All you need to do is to insert a piece of, for example, pantyhose, between the two parts and click them together. The filter itself attaches to the shaft of the microphone as a clip. ...
thingiverse
Print Settings Printer: MP Select Mini Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.0875 and 0.175 Infill: 20% AND 100% Notes: -Scew and Nut should be printer as follow: Resolution: 0.0875 Infill: 100% Speed: 30mm/s or slower than...
thingiverse
Key differences from other mounts was the use of through-hole bolt-in mounts, a cord-clip, and precise thread printing for the 5/8-27 Microphone mount on the Blue Snowball and Blue Snowball iCE's OEM Stand. What you Need For this Mount...
thingiverse
**Required Materials** - 1 Adjustable Stand (included with your Blue Snowball iCE) - 4 Hair Ties **Notes** You'll need to remove the legs from the adjustable stand. ... **Changelog** - Added an elongated version of the outer mount to accommodate...
thingiverse
Utilized another users threading attachment for the blue snowball and modeled some couplers to be able to attach to the end of the arm. Extremely solid, however, the mic couplers have not had enough testing so use at your own caution. Bolts need to...
thingiverse
Mic/camera stand for over your monitor/tv, adjust it for your model. ... This exact is for the Blue snowball mic. ... Use PLA with infill at 10-20%
thingiverse
A pop filter for your Blue Snowball mic. The shield itself is a used dryer sheet. ... Since this is parametric, you could theoretically use this on other mic stands with some experimentation.
thingiverse
... stand does require these rubber bumpers. 10mm x 4mm https://amzn.to/2HCik22 You may also be able to find them at your local hardware store. Rather buy it? Get it here: https://www.etsy.com/listing/897026717/blue-snowball-low-profile-stand
thingiverse
... one I found here was wayy too big. ...This one is made to perfectly fit the silver "stem" that screws into the blue snowball. ----------------------------------- Very easy print, supports only needed if the look is a concern. ...support angle 60
thingiverse
Bracket mount for a Blue Snowball ICE, attaches to the back of a monitor suits 100mm distance between two bottom screws (longer screws may be required). does bounce around when moving the monitor, but stays still when not touched. ...great to keep it...
thingiverse
I created a fairly simple shock absorber for my Blue Snowball. You will need: 2 x inner ring pieces 2 x outer ring pieces superglue 8+ hair bobbles Thread the bobbles through each loop and hook onto neighbouring pins. The microphone should...
myminifactory
I wanted to practice making 3d printed threads, and I wanted a new microphone stand. So here is my collection of dead simple stands for the Blue Snowball microphone. There is a super short one that might be usefull for gaming or putting on a shelf....
thingiverse
I removed the tripod mount from my Blue Snowball iCE microphone and wanted to reuse it as a camera mount for OctoPrint. It has a GoPro mount on top of a simple threaded "block" to screw onto the tripod mount threads. This was my first real...
thingiverse
A low profile 20mm tall stable stand for the Blue Snowball mic as others I had seen and tried didn't provide the stability I'd like (I'm pretty clumsy). I have used rubber foam pads on the base to reduce noise, this worked very well. ... The mic...