blue snowball mic stand 3d models
191006 3d models found related to blue snowball mic stand.myminifactory
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...
thingiverse
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion...
thingiverse
Remix of clypp's design (https://www.thingiverse.com/thing:4315674) Used for the Blue Snowball iCE microphone, particularly for the models where you can't screw off the stand. This revision makes it so the parts wrap around the stand. Previously, you...
thingiverse
Microphone stand for Yeti blue snowball mic. ...I wanted to make it shorter, but the USB cable angles down, so this gives the cable enough clearance, while still lowering the mic under my monitor.
thingiverse
... part, as it contains M15.5x1.0 thread, which is pretty fine and could turn out not well enough). No supports required. This model is set remixed as the thread to the mic stand is taken from the 'Blue Snowball Mic Armature Mount' by Janbro. ...
thingiverse
Utilized another users threading attachment for the blue snowball and modeled some couplers to be able to attach to the end of the arm. Extremely solid, however, the mic couplers have not had enough testing so use at your own caution. Bolts need to...
thingiverse
This is a short desk stand for the Blue Snowball microphone. I designed this to be able to fit the mic below my monitors. The existing designs I found didn't have any space between the base plate and the mic meaning it wasn't possible to tilt the...
thingiverse
a shorter stand for the blue snowball microphone, or softballs i'm not your mother.
thingiverse
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball. I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. I used dynamic layer height in...
thingiverse
Needed a small form factor pop filter for my snowball mic and i didn't feel like spending 20$ on a few cents worth of plastic, print 2 of the mesh holders, glue a piece of thin fabric/mesh between them before gluing them into the model itself. ... 2...
thingiverse
... stand does require these rubber bumpers. 10mm x 4mm https://amzn.to/2HCik22 You may also be able to find them at your local hardware store. Rather buy it? Get it here: https://www.etsy.com/listing/897026717/blue-snowball-low-profile-stand
thingiverse
I created a fairly simple shock absorber for my Blue Snowball. You will need: 2 x inner ring pieces 2 x outer ring pieces superglue 8+ hair bobbles Thread the bobbles through each loop and hook onto neighbouring pins. The microphone should...
myminifactory
I wanted to practice making 3d printed threads, and I wanted a new microphone stand. So here is my collection of dead simple stands for the Blue Snowball microphone. There is a super short one that might be usefull for gaming or putting on a shelf....
thingiverse
The assembly for holding the legs of my microphone to the stand craked around the hole for the screw, probably due to overtightening. This lead to the lower part of the microphone stand becoming loose, and it would spin whenever I picked up the...
grabcad
This should fit any variation of the blue snowball mic, but if it doesn't just hit the hands with a gentle heat gun and use the mic to deform them to fit.
thingiverse
Made this to keep my Blue Snowball from rolling off the desk and wrecking house. Enjoy! ...Threads made possible by: https://www.thingiverse.com/thing:193647 Print Settings Printer Brand: Printrbot ...
thingiverse
This is a simple gadget to attach a Blue Snowball (or other) microphone to a standard "lamp arm" and it also includes a pop filter. The bird is not included :-) Arm_long.stl and ring_center.stl have to be glued together. I've included the...
thingiverse
Use this part to mount Blue Snowball to your table lamp stand.
thingiverse
An ultra low profile stand for the Blue Snowball stand. 5/8-27 mount for the mic. Just enough clearance to fully tilt the microphone on the screw. 70mm diameter base ensures the microphone won't tip or roll while still being a small footprint...
prusaprinters
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball.I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. ...The stand is slim, but sturdy and sits...
thingiverse
Blue Yeti Mic Stand Spacer Lost the spacer to my Blue Yeti microphone and designed this replacement spacer.
thingiverse
My improvement, is that the shockmount can be used on the original Blue Snowball microphone stand. One M3 screw is needed for mounting the outer ring to the threaded part. And of course, some rubber bands or hair ties to mount the microphone. The...
thingiverse
This is a mic stand for the Blue Ice Mic. The one that comes with the mic is a bit too tall for my liking so I made this one. Threadless design so it fits snuggly in the bottom of the mic. ...I printed it upsidedown with a 6mm brim but other printers...
thingiverse
Hey guy today I bring you a simple and yet effective adapter for the SnowBall mic . ...I printed at 50% infill Subscribe to MrJefferson105 Print Settings Printer Brand: Prusa ...
thingiverse
I designed this, because the normal max hight is not enough for me. ... I printed this with 20% infill, no raft and no support.
thingiverse
Just a stand I threw together for my Blue Yeti mic. ... It assumes you are not using a 90 degree cable, if you are there are better options.
thingiverse
I wanted a smaller and shorter mic stand than all the ones out there, so after a couple of tries, I came up with this one. It's quite stable and the little curve holds up to the mic's weight very well. ...
thingiverse
This works with the Blue Yeti USB mic that measures approx 70mm OD at the side mounting screws. [The exact mic I have came with an arm for edge-of-desk mounting.](https://www.amazon.com/gp/product/B078MHS3SC/) You'll need to print 2 of the spacers...