blue snowball microphone stand 3d models
197591 3d models found related to blue snowball microphone stand.myminifactory
I wanted to practice making 3d printed threads, and I wanted a new microphone stand. So here is my collection of dead simple stands for the Blue Snowball microphone. There is a super short one that might be usefull for gaming or putting on a shelf....
thingiverse
This lead to the lower part of the microphone stand becoming loose, and it would spin whenever I picked up the microphone. I created this replacement part from the original design, with some minor tweaks. A long lifetime for this piece is not...
thingiverse
I designed this, because the normal max hight is not enough for me. ... I printed this with 20% infill, no raft and no support.
prusaprinters
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball.I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. ...The stand is slim, but sturdy and sits...
thingiverse
My improvement, is that the shockmount can be used on the original Blue Snowball microphone stand. One M3 screw is needed for mounting the outer ring to the threaded part. And of course, some rubber bands or hair ties to mount the microphone. The...
thingiverse
I wanted a way to hold the microphone just above the monitor in my office rather than on the desk to the side or in front of me, blocking the screen (the tripod's lowest height is too high). These three brackets allow the whole thing to be hung from...
thingiverse
a shorter stand for the blue snowball microphone, or softballs i'm not your mother.
thingiverse
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball. I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. I used dynamic layer height in...
thingiverse
Very simple low desk stand for my snowball microphone.
myminifactory
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...
prusaprinters
Pop filter which connects to a Blue Microphone.Add a couple layers of thin fabric will do a decent job of blocking your puffs of air.One of the securing rings has space for a 6mm inner diameter spring to help press it against the outer ring.Mounting...
thingiverse
A cheap and easy solution to convert your snowball into a handheld mic. ... Video on the topic: https://youtu.be/DdlsjZNpgUU
thingiverse
... stand does require these rubber bumpers. 10mm x 4mm https://amzn.to/2HCik22 You may also be able to find them at your local hardware store. Rather buy it? Get it here: https://www.etsy.com/listing/897026717/blue-snowball-low-profile-stand
thingiverse
I created a fairly simple shock absorber for my Blue Snowball. You will need: 2 x inner ring pieces 2 x outer ring pieces superglue 8+ hair bobbles Thread the bobbles through each loop and hook onto neighbouring pins. The microphone should...
thingiverse
I lost the stock stand for my Blue Yeti USB microphone, so I designed this stand with a slot for the oval extrusion on the bottom of the microphone to fit into. There is a slot for the USB cable to fit into, but I did not design a similar slot for...
cults3d
This is my single part Pop Filter for my Blue Snowball Microphone. The pop filter can be installed easily between the tripod and the microphone bowl due to the 16mm hole. Stretch tights around the ring and press a 5mm soft rubber (or elastic band or...
thingiverse
This is my single part Pop Filter for my Blue Snowball Microphone. The pop filter can be installed easily between the tripod and the microphone bowl due to the 16mm hole. Stretch tights around the ring and press a 5mm soft rubber (or elastic band...
thingiverse
An ultra low profile stand for the Blue Snowball stand. 5/8-27 mount for the mic. Just enough clearance to fully tilt the microphone on the screw. 70mm diameter base ensures the microphone won't tip or roll while still being a small footprint...
thingiverse
Use this part to mount Blue Snowball to your table lamp stand.
grabcad
This should fit any variation of the blue snowball mic, but if it doesn't just hit the hands with a gentle heat gun and use the mic to deform them to fit.
thingiverse
Made this adaptor to enable the fitting of the Yeti to the Snowball ringer mounting frame. ...Added a bracket to enable the attaching of a pop screen
thingiverse
You will need to design/find a way to mount it to a stand or a tripod, i left some some lower holes for that. Print all the necessary parts (you only need one outer ring) You will need to dismantle the tripod that came with the mic. ( or use a 5/8"...
cults3d
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion 360...
thingiverse
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion...
thingiverse
This is an adapter plate allowing you to attach a snowball mic to most kinds of tripods as well as a variety of other camera mounting equipment. ... This is a remix (see relevant link) and also uses the openscad thread function found here:...
thingiverse
ad895 had made the design for the original nice all metal Snowball stand. I wasn't as lucky when I bought mine, and got the other cheap, partly plastic, stand. The mount needed some changes as the stands have different diameters. The downscaled...