blue snowball shockmount 3d models
41653 3d models found related to blue snowball shockmount.
thingiverse
My improvement, is that the shockmount can be used on the original Blue Snowball microphone stand. One M3 screw is needed for mounting the outer ring to the threaded part. And of course, some rubber bands or hair ties to mount the microphone. The...
thingiverse
a shorter stand for the blue snowball microphone, or softballs i'm not your mother.
thingiverse
Simple stand to replace my blue snowball mount (non-adjustable) after I accidentally dropped and broke the original one
thingiverse
A clamp and screw created to hold your blue snowball microphone. ...Prints in three different pieces designed to require no glue, all pieces should fit together snugly.
thingiverse
Remix of my original blue snowball mount, 2 Sizes small and large, Addeds some adjusta ability on hight. 6 x M4x8 required for hight adjustablity. ...
thingiverse
This is a pop filter I designed to work with a Blue Snowball microphone. I super glued part 1 into part 2. ...then stretched a knee high stocking over the hoop trimmed it up a bit and used a rubber band to cinch it up at the bottom.
myminifactory
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...
thingiverse
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball. I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. I used dynamic layer height in...
thingiverse
This is a pop-filter for the "Blue Snowball" microphone. All you need to do is to insert a piece of, for example, pantyhose, between the two parts and click them together. The filter itself attaches to the shaft of the microphone as a clip. ...
thingiverse
Key differences from other mounts was the use of through-hole bolt-in mounts, a cord-clip, and precise thread printing for the 5/8-27 Microphone mount on the Blue Snowball and Blue Snowball iCE's OEM Stand. What you Need For this Mount...
thingiverse
I printed and assembled a shock mount for my Blue Yeti Microphone from Thingverse. When I tried to attach the mount to my microphone boom I needed to fill in some space. Regular washers were tricky to position so I designed one with an open bottom...
thingiverse
Mic/camera stand for over your monitor/tv, adjust it for your model. ... This exact is for the Blue snowball mic. ... Use PLA with infill at 10-20%
thingiverse
A pop filter for your Blue Snowball mic. The shield itself is a used dryer sheet. ... Since this is parametric, you could theoretically use this on other mic stands with some experimentation.
thingiverse
... stand does require these rubber bumpers. 10mm x 4mm https://amzn.to/2HCik22 You may also be able to find them at your local hardware store. Rather buy it? Get it here: https://www.etsy.com/listing/897026717/blue-snowball-low-profile-stand
thingiverse
**Required Materials** - 1 Adjustable Stand (included with your Blue Snowball iCE) - 4 Hair Ties **Notes** You'll need to remove the legs from the adjustable stand. ... **Changelog** - Added an elongated version of the outer mount to accommodate...
thingiverse
Utilized another users threading attachment for the blue snowball and modeled some couplers to be able to attach to the end of the arm. Extremely solid, however, the mic couplers have not had enough testing so use at your own caution. Bolts need to...
thingiverse
... one I found here was wayy too big. ...This one is made to perfectly fit the silver "stem" that screws into the blue snowball. ----------------------------------- Very easy print, supports only needed if the look is a concern. ...support angle 60
thingiverse
Bracket mount for a Blue Snowball ICE, attaches to the back of a monitor suits 100mm distance between two bottom screws (longer screws may be required). does bounce around when moving the monitor, but stays still when not touched. ...great to keep it...
thingiverse
I created a fairly simple shock absorber for my Blue Snowball. You will need: 2 x inner ring pieces 2 x outer ring pieces superglue 8+ hair bobbles Thread the bobbles through each loop and hook onto neighbouring pins. The microphone should...
myminifactory
I wanted to practice making 3d printed threads, and I wanted a new microphone stand. So here is my collection of dead simple stands for the Blue Snowball microphone. There is a super short one that might be usefull for gaming or putting on a shelf....
thingiverse
I removed the tripod mount from my Blue Snowball iCE microphone and wanted to reuse it as a camera mount for OctoPrint. It has a GoPro mount on top of a simple threaded "block" to screw onto the tripod mount threads. This was my first real...
thingiverse
A low profile 20mm tall stable stand for the Blue Snowball mic as others I had seen and tried didn't provide the stability I'd like (I'm pretty clumsy). I have used rubber foam pads on the base to reduce noise, this worked very well. ... The mic...
thingiverse
... part, as it contains M15.5x1.0 thread, which is pretty fine and could turn out not well enough). No supports required. This model is set remixed as the thread to the mic stand is taken from the 'Blue Snowball Mic Armature Mount' by Janbro. ...
thingiverse
Had my Snowball behind my monitors due to room on my desk, but after seeing the short desk stand by mrzood, I had an idea to mount it on top of my monitor to move it even further out of the way. ... Print Settings Printer: ...
thingiverse
For use with the Ikea TERTIAL stand. The largest holes is designed for M5 bolts and the smaller for M3. EDIT: Some users have experienced problems with the scale of the parts being to small. Make sure to check your import settings and make sure they...