blue snowball stand 3d models
188304 3d models found related to blue snowball stand.thingiverse
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball. I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. I used dynamic layer height in...
myminifactory
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...
thingiverse
a shorter stand for the blue snowball microphone, or softballs i'm not your mother.
myminifactory
I wanted to practice making 3d printed threads, and I wanted a new microphone stand. So here is my collection of dead simple stands for the Blue Snowball microphone. There is a super short one that might be usefull for gaming or putting on a shelf....
thingiverse
The assembly for holding the legs of my microphone to the stand craked around the hole for the screw, probably due to overtightening. This lead to the lower part of the microphone stand becoming loose, and it would spin whenever I picked up the...
thingiverse
I designed this, because the normal max hight is not enough for me. ... I printed this with 20% infill, no raft and no support.
thingiverse
... stand does require these rubber bumpers. 10mm x 4mm https://amzn.to/2HCik22 You may also be able to find them at your local hardware store. Rather buy it? Get it here: https://www.etsy.com/listing/897026717/blue-snowball-low-profile-stand
thingiverse
I created a fairly simple shock absorber for my Blue Snowball. You will need: 2 x inner ring pieces 2 x outer ring pieces superglue 8+ hair bobbles Thread the bobbles through each loop and hook onto neighbouring pins. The microphone should...
thingiverse
My improvement, is that the shockmount can be used on the original Blue Snowball microphone stand. One M3 screw is needed for mounting the outer ring to the threaded part. And of course, some rubber bands or hair ties to mount the microphone. The...
thingiverse
An ultra low profile stand for the Blue Snowball stand. 5/8-27 mount for the mic. Just enough clearance to fully tilt the microphone on the screw. 70mm diameter base ensures the microphone won't tip or roll while still being a small...
thingiverse
Use this part to mount Blue Snowball to your table lamp stand.
prusaprinters
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball.I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. ...The stand is slim, but sturdy and sits...
thingiverse
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion...
thingiverse
ad895 had made the design for the original nice all metal Snowball stand. I wasn't as lucky when I bought mine, and got the other cheap, partly plastic, stand. The mount needed some changes as the stands have different diameters. The downscaled...
thingiverse
Remix of clypp's design (https://www.thingiverse.com/thing:4315674) Used for the Blue Snowball iCE microphone, particularly for the models where you can't screw off the stand. This revision makes it so the parts wrap around the stand. Previously, you...
thingiverse
Simple stand to replace my blue snowball mount (non-adjustable) after I accidentally dropped and broke the original one
thingiverse
Remix of my original blue snowball mount, 2 Sizes small and large, Addeds some adjusta ability on hight. 6 x M4x8 required for hight adjustablity. ...
thingiverse
A clamp and screw created to hold your blue snowball microphone. ...Prints in three different pieces designed to require no glue, all pieces should fit together snugly.
thingiverse
This is a pop filter I designed to work with a Blue Snowball microphone. I super glued part 1 into part 2. ...then stretched a knee high stocking over the hoop trimmed it up a bit and used a rubber band to cinch it up at the bottom.
thingiverse
This is a pop-filter for the "Blue Snowball" microphone. All you need to do is to insert a piece of, for example, pantyhose, between the two parts and click them together. The filter itself attaches to the shaft of the microphone as a clip. ...
thingiverse
... ... The stand and outer ring is designed with zero gap between them for a tighter fit. ... The inner ring has the exact diameter of the microphone itself and can be pressed around the ring that connects the front and back side of your microphone.
thingiverse
Key differences from other mounts was the use of through-hole bolt-in mounts, a cord-clip, and precise thread printing for the 5/8-27 Microphone mount on the Blue Snowball and Blue Snowball iCE's OEM Stand. What you Need For this Mount...
thingiverse
Mic/camera stand for over your monitor/tv, adjust it for your model. ... This exact is for the Blue snowball mic. ... Use PLA with infill at 10-20%
thingiverse
A pop filter for your Blue Snowball mic. The shield itself is a used dryer sheet. ... Since this is parametric, you could theoretically use this on other mic stands with some experimentation.