bluerobotics 3d models
55 3d models found related to bluerobotics.thingiverse
Bracket that allows attachment of a bluerobotics light to 3030 aluminum rail (or anything really).
grabcad
The BlueROV is an open-source remotely operated vehicle (ROV) for exploring underwater. ...Check it out at www.bluerobotics.com/store/rov/bluerov/.
grabcad
The Heavy Retrofit Kit provides some powerful new capabilities: six degree-of-freedom control, active roll and pitch stability, and additional lifting capability.If you're looking for one, you can find one...
grabcad
... T200 Thruster is a low-cost high performance thruster for marine robotics. ...It was originally launched in 2014 through a Kickstarter campaign.If you're looking for one, you can find one at:https://www.bluerobotics.com/store/thrusters/t200-thruster/
grabcad
... T100 Thruster is a low-cost, high performance thruster for marine robotics. ...It was originally launched in 2014 through a Kickstarter campaign.If you're looking for one, you can find one at:https://www.bluerobotics.com/store/thrusters/t100-thruster/
grabcad
The Electronics Tray mounts to a 4” Watertight Enclosure O-ring Flange, so you don’t need any tools to access your electronics.If you're looking for one, you can find one...
grabcad
... stable, yet highly maneuverable. The BlueROV2 provides the capabilities of a high-end commercial mini-ROV at the price of the most basic commercial ROVs.If you're looking for one, you can find one at:https://www.bluerobotics.com/store/rov/bluerov2/
thingiverse
Heavy 4 inch Dome ring for bluerobotics rov with this ring it's much stronger
cults3d
Fin for electric SUP. ...Designed for thruster: https://bluerobotics.com/store/thrusters/t100-t200-thrusters/t200-thruster/ Fin box has two degrees angle regarding the waterline. ... The model was intensively tested at sea.
thingiverse
this is an adapter for the BlueRobotic T200 thruster that will fill the mast i made for it
thingiverse
Simple 2 parts collar, 2mm holes for 4" bluerobotics rov enclosure. ... It's a base for 4 hard points (Handle on top, motors on sides and batterie on bottom) : - Mount for 90° 16mm tube https://www.thingiverse.com/thing:4582837 - Mount for 60° 16mm...
thingiverse
This is a 4.5mm thick flat skeg designed to sweep debris around a Blue robotics T100 or T200 thruster. it is made for use with a flat bottom hull. There is area on the bottom of the mount for caulking around the through bolts, though you may want to...
prusaprinters
<p>This is a 4.5mm thick flat skeg designed to sweep debris around a Blue robotics T100 or T200 thruster. it is made for use with a flat bottom hull. There is area on the bottom of the mount for caulking around the through bolts, though you may want...
thingiverse
60° 16mm tube mount 2 versions : - 16,25 mm - 16,50 mm Supposed to be mounted on collar https://www.thingiverse.com/thing:4582804
thingiverse
16mm tube mount 4mm holes for fastening Supposed to be mounted on collar https://www.thingiverse.com/thing:4582804
thingiverse
16mm tube mount 2 versions : - 16,25 mm - 16,50 mm Supposed to be mounted on collar https://www.thingiverse.com/thing:4582804
thingiverse
the BlueRobotic populare T200 thruster : this the mast extension
grabcad
This is the Blue Robotics SwitchBlox, a collaboration between BlueRobotics and BotBlox
thingiverse
MATE underwater [analog camera](https://www.bluerobotics.com/store/sensors-sonars-cameras/cameras/low-light-ntsc-camera/) board mount. ... A wholehearted thanks to [Blue Robotics](https://www.bluerobotics.com/) for their support.
thingiverse
18650 battery case for use in a bluerobotics 4 inch aluminum housing. ...Cells are in a 3s16p configuration.
thingiverse
These are the blue robotics m100 thrusters from https://www.bluerobotics.com/store/thrusters/m100-p-propeller-rev-r1/
thingiverse
... competition. ... Fits on 500gph bilge pump. Adapted from Bluerobotics M100 propeller - https://www.bluerobotics.com/store/parts/m100-p-propeller-rev-r1/ This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/ehMyLngtlj7
thingiverse
A new version of the BlueRobotics T100 Thruster design to accommodate the NTM 28-30S $10 brushless motor. ...OnShape repo: https://cad.onshape.com/documents/5e780ea7ca73f7fe579106cb/w/d291538ecc436957abffcbac/e/24e473f6fc938fc2ad4aa708 Print Settings...
thingiverse
Tool for porting the wire penetrators from BlueRobotics. I designed this to help make the wires straight when filling the penetrators with epoxy, and keep it fixed during the 24 hour curing. ...The small stick in the buttom is for mounting it in a...
thingiverse
... camera tripod mount. ... The hexagonal hole in the mount is designed to accept a stainless 1/4-20 nut for attachment to a standard tripod head bolt. A wholehearted thanks to [Blue Robotics](https://www.bluerobotics.com/) for their support.
thingiverse
A focus cone for lumen lights from BlueRobotics. ... I found the flight to be too dispersed, i could have changed the lens to a flat Acrylic plate (which i did) but still found side scattering so these help focus the light into one spot.
thingiverse
... BlueDrive Power Fin, Current Drives Electrafin, etc Not tested for maximum speed yet. Inspired by bluerobotics T200 thruster. ... RC: 18650 / Nano / nRF24 / WS2812 / Potentiometer Motor: F4125 / 6s4p battery / ESC 6s 70A / Nano / nRF24
thingiverse
This part is for mounting a [Blue Robotics low-light USB camera](https://bluerobotics.com/store/electronics/cam-usb-low-light-r1/) in a [FitStill Dive Housing Case for GoPro Hero 5...