bmw ipad dash mount 3d models
360848 3d models found related to bmw ipad dash mount.thingiverse
This is the rear mount for the K1S dash cam in a BMW 1 Series Convertible (E88). It clips in on the rear vent and under the roof cover and does not need any adhesive, the just mount your camera on top of it (you will need to invert the camera...
thingiverse
I used to sit my iPad mini in the pull out tray in the center below the dash and use it as a dedicated GPS on long road trips, but I got tired of it sliding around and being so low in my field of view, so I remixed the excellent iPad mini holder by...
thingiverse
This is an alternative to another iPad mini mount that I created for my fan attack Clubsport VE2.5 wheelbase. This one mounts to the side instead of on top. It can also be printed in one piece. It will simply mount using the existing bolts on the...
thingiverse
... it on smaller size printer beds. ...So you will have to glue part one to the back of part two before mounting it on your Clubsport wheelbase. This bracket will hold A standard iPad mini in landscape format allowing for data port access on either side.
thingiverse
Simple dash stand for iPad or iPhone with otter Box. Design for holding a iPad in our work truck to use Google maps. Just put two way tape on the bottom and it should keep your iPad with Otter box in place. ...
thingiverse
... to pay for original and aem ones dont last one use. I printed them with support on their sides so the opening is going up and down as this doesnt rely on layer adhesion for strength. "dash clip 1" is the dash clip "clip 3" is the door clip
thingiverse
... if you're planning on taking the cover often so if you want it to hold on longer and be tighter/stronger then you might aswell use the ABS filament but PLA should be enough. It perfectly fits in BMW E60 2003 so it should fit aswell in other models
thingiverse
This project requires some creativity to mount to dash and put the charger in the one side. I had to glue the halves together and drill a hole through the printed piece and use epoxy to secure the charge cord, which is an adapter to have an aux...
thingiverse
Just needed something to hold a magsafe charger in my car, I drilled this into a hidden part on the dash to hold my phone. ...the ball is 17mm diameter and should fit gps type stuff.
thingiverse
BMW E46 dash trim mounting clip. ...Part number: 51458266814 - Insert Rot.
thingiverse
If you don't have an Android unit, nice iPad Mount can help. Standard version is for left hand side cars, but if you mirror it, then you can fit into RHD. On the left side you have place for Jack 3,5. I was printing without support. I was...
thingiverse
Ipad mini dash kit for volvo v60, this only fits the model with the 5 inch screen. ... No glue or double sided tape needed, this snaps into place as seen in the video: https://youtu.be/SOsNidMuVBo
prusaprinters
Dieser Halter ist für das ipad erstellt. ...Er ist klein, stabil, handlich und einfach zum drucken. This holder is made for the ipad. ...It is small, stable, handy and easy to print.</p>
cults3d
this is a model of the clips thats on the Bmw e46 dashboard best to print in ASA or abs ! :) Pla tends to break, caused by the stiffness.. plug and play! ... fits perfect in my own car :)
thingiverse
Designed this "bolt" for my BMW E46 and it fits like a glove. Printing: Whatever really, I used a Flashforge Adventure 3 and used the standard settings but chose the low (fast) selection since it started as a prototype but it worked out just...
thingiverse
... gluing together (I used JB Weld Plastic Epoxy). To mount I used Scotch Extreme Double Sided mounting tape. It has been almost 1000 miles and it's holding up very well. I printed in PETG for durability, PLA won't cut it in a car environment. ...
thingiverse
This is just a little edited version of a mount, made to be slightly stronger and to better fit iPad's with Cases on like mine. You can use average print settings for this - Doesn't need support if you print it upright I hope you enjoy! ...
thingiverse
Simple design to mount any ball joint phone mount on VW Amarok Dash
thingiverse
This is a simple dash mount phone holder for an RX8. ...It follows the contours of the dash and allows a magnetic mount to stick to it.
thingiverse
Mounts right on vrs upper bolts. ...Its 60mm long and dash mounting end bolts are 112mm apart with 5mm holes.
thingiverse
This is a simple dash mount I remixed to hold a backup camera screen for my RV, it would also work well as a phone mount with a magnet mount.
thingiverse
For dash mount style panels where the mounting screw holes in the corners have broken off. AC panel in the boat is re-mounted good as new! ... Instructions Makerbot 2 Black filament, 0.2mm 1 layer 100%...
thingiverse
This is a dash mount for a Vapor on a DR650. Mounts between handle bar risers. I used brass inserts and m5 bolts to attach. ...I printed with carbon infused nylon but petg should work also.
thingiverse
On my black dash in the sun, it gets hot enough that PETG starts to sag and warp.** This is a dash mount I designed to go with a phone holder I designed for Autocross events. I have attached it to the dash using some of the 30lb Double sided 3M...
thingiverse
This is a rugged dash mount for a 2014-2019 C7 Corvette. It uses the AMPS screw pattern to attach accessories and I used ProClip mounts to attach a RasPi running OpenAutoPro. I used PLA because it's all I have but the design is reinforced and using...
thingiverse
Adapter to mount the Cygolite Dash to a GoPro style mount. No hardware required, just use the screw that's holding the loop onto the light. For increased stability, I added some zip ties onto the GoPro mounting point. ... This is still a work in...
thingiverse
- Xiaomi Yi Smart Dash Camera mount - Didn't want to remove original mount from my car when I traveled abroad and wanted to use the camera in rented vehicle... ... - Printed in PETG, 236C, 100%infill, 25% fans - Use thick, double sided tape to stick it...