bno055 imu 3d models

This is a housing component designed to hold the Adafruit BNO055 IMU. It is intended for use on FTC robots. It is recommended to use 2-56 screws to secure the circuit board to the housing. If you printer makes holes slightly smaller, you should be...

This is a holder for a BNO055 IMU from adafruit, designed to connect with Tetrix pieces. Print Settings Printer Brand: MakerBot Printer: ...

PCB of Adafruit's BNO055 9-DOF Absolute Orientation IMU featuring STEMMA QT connection.Modeling performed in Fusion360 based on the PCB fabrication print found on the product's overview page...

This a holder for the BNO055 unit from Adafruit (https://learn.adafruit.com/adafruit-bno055-absolute-orientation-sensor/overview). It's designed to bolt into the hole spacing for Tetrix which is used in FTC robotics competitions. You'll need tiny...

This is a simple housing for the Adafruit BNO055 IMU.

BNO055

BNO055Data sheet - https://cdn-shop.adafruit.com/datasheets/BST_BNO055_DS000_12.pdf

A Modern Robotics CDIM Mount with integrated BNO055 IMU from Adafruit. Just hot glue the IMU into the holder after soldering the wires and connect to the CDIM. ... Mount using CDIM holes and adds very little extra space as it uses the corner where the...

Adafruit BNO055 Absolute Orientation Sensor

BNO055 Bosch MEMs IMU box

Inertial Measurement Unit (IMU)

This is a makeshift strap holder for the Shimmer IMU. ... 3D prints worked well for me.

A simple 3d printed holder for the Sparkfun IMU Digital Combo-6dof. ...With mounting holes.

CAN IMU box from basecam electronic for the famous hobby gimbal BGC-005 MAX, to connect to tilt

It is a case for Adafruit LSM6DS3TR-C 6-DoF Accel + Gyro IMU - STEMMA QT / Qwiic (https://www.adafruit.com/product/4503). I think this is a relatively new IMU so I could not find an existing case. ...This is what I ended up with after a number of...

IMU VrBrain Virtualrobotix

Dji A2 IMU

Arduino MKR IMU Shield;Acceleration sensorI2C

https://www.basecamelectronics.com/i2c_imu/#specs-tabBaseCam SimpleBGC 2nd IMU

IMU: 9 DoF MARG MPU9250 & Adafruit LSM6DSOX + LIS3MDL

intelligent 9 - axis absolute orientation sensor

Three pieces with main case, cover and button for Razor 9DoF IMU.

Kalibrierhilfe GY-801 ==================== Kalibrierhilfe um den IMU GY-801 einfacher kalibrieren zu können.

IMU standoffs for the Paparazzi Lisa/L autopilot (http://paparazzi.enac.fr/wiki/User/LisaL)

... ... The IMU we used was a Mulit-Axis GY-80 IMU (as seen in an uploaded image) and the case was designed for that, the model of the IMU was a quickly done in order to make sure holes lined up. The team 3D Printed the cases and they worked really well.

... designed to hold the new Xsens DOT inertial measurement units (IMU). ... The bracket is useful for affixing the IMU to people or objects for tracking. We found the bracket was helpful for placing the IMU on the tibia with the assistance of Coban wrap.

IMU calibration tool allowing quck rotations it within each 90-degree face for all axis. ... Some openings and spaces to output cable

this is for second can imu referred to famous hobby gimbal BGC 005 MAX, can put this item vertical bracket attached to pan before roll motor

3D printed case for Gadgeteer Pigeon IMU 3-axis magnetometer, accelerometer, and gyro Case was designed for our 2019 FRC Competition robot. ...

IMU case with exposed pins: VCC GND SCL SDA EDA ECL AD0 INT For those looking to add a case to their MPU-9250 or similar IMU. Supports straps up to 38mm in width. ... Supports M3 screws and nuts (suggest nylon)