body for traxxas rustler 3d models
2324384 3d models found related to body for traxxas rustler.cults3d
I designed this body for my brother's Traxxas Rustler. He thought the use of a 30's body would fit the chassis well. Being a 2wd version I thought that a 32 coupe hot rod would look good. He was right. It fits well. The cab is chopped and...
cults3d
They just go straight over the original mounts and you put the body pins through to hold them in place. All you need is some m4 screws and nuts to match (Maybe some superglue if the nut is not tight enough). I had to cut the screws to the right...
thingiverse
... through the hole in the top of the mount and superglued them there. Next, you put the nuts in the mount screws and superglue them. (Its a little hard to get the body pins through but after a few times you get the hang of it) Feel free to comment
thingiverse
This is a custom rear mount post that allows a Rustler body shell to be used on a Stampede chassis. ... Print Settings Printer: Wanhao Duplicator 4 ...
thingiverse
This is some of the plastic body parts for a Traxxas Rustler. I used a dial caliper and ruler to measure the parts and used SolidWorks to build them. ...Parts are not 100% accurate and if printed will need sanding and/ or drilling for proper fit.
thingiverse
these help prevent the body pin from going under the car's body
prusaprinters
Illumination Kit for Traxxas Rustler Material: PETGLayerheight: 0.2mmInfill: 50%More in our blog: https://makerteam.de/blog/traxxas-rustler-illumination/
thingiverse
QuicRun Electronic Speed Control adapter for Traxxas Rustler. ...Some minor mods may be done to meet your needs.
thingiverse
Rear Mount extension for larger body in a Traxxas Stampede 2wd
cults3d
I made these brackets to add tail lights and front running lights to my Traxxas Rustler. Luckily the track area for our Saturday night drag races is well lit, but the slow down and turn around area is not, so lights are a big help in getting the car...
thingiverse
I made these brackets to add tail lights and front running lights to my Traxxas Rustler. Luckily the track area for our Saturday night drag races is well lit, but the slow down and turn around area is not, so lights are a big help in getting the car...
prusaprinters
I've installed this in my Rustler and it fits perfectlyHere is a link to the product page for the real part: https://traxxas.com/products/parts/3632AIf you look at the model from the bottom up the caster block on the right is the right caster block...
thingiverse
I designed a simple but sturdy camera mount for a Traxxas Rustler to get some FPV action. It's intended to hold a Maxxter action camera, but will suit any camera with M6 thread. It uses an M6 round head square neck bolt and a lock nut, to mount...
thingiverse
(V1.0 - August 10, 2020): *Features:* - More mounting options for front and rear wing - Much more durable wing design, can handle flips easily now - More downforce - Much easier to print (No supports needed!) - Lower print time, less filament...
prusaprinters
This is a new version of the wing system I created back in 2017, now more printable and modular than ever! (V1.0 - August 10, 2020): Features: More mounting options for front and rear wing Much more durable wing design, can handle flips easily now...
pinshape
... ... I had cracked the hub that hold the bearings for the rear axle. Although I glued the pieces back together, I figured that I might as well model the part and make it available here. :) I just did a test run in the street, and the car runs great!
thingiverse
... ... I had cracked the hub that hold the bearings for the rear axle. Although I glued the pieces back together, I figured that I might as well model the part and make it available here. :) I just did a test run in the street, and the car runs great!
thingiverse
For rough draft or faster prints, I used 0.2mm The disc on the left fits my first gen Rustler body posts and the one on the right fits the body posts of the e-maxx. After letting a young man drive the emaxx and having him wreck it and pull the body...
thingiverse
Update 1: I just printed it out and from visual and caliper inspection it is very close the the actual part Update 2: I installed this in my Rustler and it fits perfectly Here is a link to the product page for the real part:...
thingiverse
This is a simple replacement wing for the stock Traxxas Rustler Body. This will use the same 4mm hardware for the original wing. ...
thingiverse
Traxxas Rustler bumper, super useful for light use such as drifting. I haven't printed it in TPU but I'm sure it would still work well. ...
thingiverse
This is the brace that holds the battery in the Rustler traxxas RC car.
myminifactory
This is a super useful bumper for a Traxxas Rustler. I use mine for drifting because it helps you bump off of things with the big cushion. ...It works super well printed in TPU but It might crack in PLA.