boe bots 3d models
14209 3d models found related to boe bots.grabcad
One of these is a 3-D representation of what our boe-bot looked like with our sensors. ...The other is an exploded view of our boe-bot.
thingiverse
Stand to support the Parallax Boe-Bot robot, while you are testing programs, holds the robot with wheels off the ground. Instructions Printed in ABS with the UP! using default settings, this was my...
thingiverse
This is a one piece mount for 3 HC-SR04 ultrasonic sensors, designed for the arduino boe-bot. ...The file has been updated to include more room for pins sticking out from the bottom of the board.
thingiverse
Simple platform to add on to BOE-BOT so that my grandson can attach his LEGO bricks and people on to the BOE-BOT. Printed with 0.2mm resolution 3 shells and 25% infill. The LEGO parts snap to it nicely. ...
thingiverse
A battery holder for the Parallax Boe-Bot, it holds a 6AA battery holder in place of the original 4AA battery holder. This is useful if using the Arduino Board of Education Shield. Instructions I...
thingiverse
This is an improved whiskers sensor support for boe-bot (https://www.parallax.com/product/boe-bot-robot). Two main objectives can be achieved with this design: 1- Reliability improvement 2- Flexibility, allowing to be installed on the front or back...
thingiverse
A colleague asked me to design an adapter plate so that he could mount a Raspberry Pi to his BOE-BOT. Here is the result (with fins). ...Print Settings Printer Brand: MakerBot ...
grabcad
is short for Board of Education robot. It is the trade name of a robot kit that is used in American college and high school robotics classes. It consists of a main circuit board (the Board of Education), a plug–in microcontroller, two servo motors...
thingiverse
This was my final project at Robotics university, this is to be used as a development kit platform for multi purpose, use as you wish. ...Spider-like robot with 6 legs but only two servos.
thingiverse
designed to use a Nano mounted on a solderless board from Radio Shack... the battery pack design in the sketchup is meant to hold a 9v, but does not (measuring errors) Which doesn't matter, since even running off the 9v, the draw from 2 servos...
thingiverse
A face plate I designed for my robot named Anton, complete with top hat. I used spare screws from the kit to secure it. ...Included a spike-less and name-less version as well.
thingiverse
This is an adaptation of a trebochet to fit on top of a Parallax BOE-Bot. It is activated by a signal from the ultrasound sensor on front of robot. The servo lifts and frees the tab holding the slinger down when it gets close to an object. Print the...
thingiverse
Ultrasonic sensor mounting bracket for the Parallax BOE Shield bot. This bracket allows you to attach the ultrasonic bracket to the front of the Parallax BOE robot. ... To install this bracket, insert the ultrasonic sensor into the bracket, attach...
thingiverse
Customized version of http://www.thingiverse.com/thing:117519 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519
thingiverse
Customized version of http://www.thingiverse.com/thing:117519 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=117519
thingiverse
Customized version of https://www.thingiverse.com/thing:43406 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=43406
cults3d
... legs just snap in I used a tiny dab of super glue to secure them but its already a snug fit. The logistic bot I used some cheap Jewlery/beading wire to make a small pin pushed through on one side and covered over with super glue so it cant back out.
thingiverse
... just snap in I used a tiny dab of super glue to secure them but its already a snug fit. The logistic bot I used some cheap Jewlery/beading wire to make a small pin pushed through on one side and covered over with super glue so it cant back out.
grabcad
... The images were rendered in the Keyshot 4.1 demo with the cool new toon shaders and the backplates were created in Photoshop. You can download the models here.. http://grabcad.com/library/cat-bots-1/files/CatBotModels.zip Thanks for taking a look!
thingiverse
The parts are designed to fit a cheap toy fan: http://www.amazon.com/Disney-Frozen-Light-up-Candy-Elsa/dp/B00LVJXFMY/ref=sr_1_1?ie=UTF8&qid=1458840850&sr=8-1&keywords=toy+fan+with+candy (You can find them for $2.50/ea at most Wal-Mart store checkout...
thingiverse
Proto-design idea for replacing the BoE Chassis with something cheaper, and more easily modified. Initial design specs modified from stock BoE chassis... Instructions Still in design phases,...
thingiverse
my simplified version of the face of Boe from Dr Who. Instructions revision 7 printed ok I had to make the tendrils attached to the head to make it print without issues. ...I'll be putting mine in a...