bone handle onewheel 3d models

The human interface engineers are diligently working on a revolutionary new design for a charging port cover and holder that will seamlessly integrate into existing devices. A comprehensive overhaul of the current charging system is underway, with...

Designed a Delete for The Float Life's Varial WTF Rails for the XR I printed mine with 3 parameters so i could sand them down and then spray them

Another user and I were interested in separate files of this mount to fit smaller print beds. I have not yet printed these, so I cannot speak to the design just yet. I figured out how to split the larger STL into two smaller STL files. ... This...

cut version of the Fender (bikini fender)

This is my own version of combining the very nice looking desing of www.thingiverse.com/thing:4771318 + the back part of this one : www.thingiverse.com/thing:4486071 I increased the with of both letters(XR) and main/base plate for extra rail...

This print barely fits my print bed 235x235mm. Make sure it fits your print bedI want to experiment with flexible filaments. And see if I can create a usable add on for the stock footpad. I wanted to test how it fills to use a soft footpad without...

IMPORTANT NOTICEI do not keep my designs updated on printables anymore. To ensure you download the the most up-to-date models,  please visit this design on my makerworld account:https://makerworld.com/en/models/20773Thanks for your support!-Kagman

More or less stock shape, compatible with stock battery housing. ...Does not incorporate cutout for tail light as my end goal was to incorporate a larger battery without using the stock housing.

This is a remix of TH-Props design, with heartfelt thanks going to the original creator, TH-Props. The link to the original design can be found on Thingiverse at https://www.thingiverse.com/thing:3273259. A few tweaks were made to reinforce the...

Hi all, I made a remix from this thing:2641409 which I want to share. I think it's a cool helmet holder for my OW XR. It is basically the same flat hand, with 2 changes : -On the fingers' length -to put them at the same height for practical...

Chopped and hacked at TickTock's excellent Pint Touch Fender to make room for the axle blocks and raised stock tire on the Pint. ...Then added a bit of plastic to reinforce some thin pieces and to better allow for mounting other pieces on the...

my feet are big so i made these to give me more room on the foot plate of the pint.i used strong double sided foam tape to hold the tip and sides and two 4mm x 12mm long flat head screws from home depot. i also added a stick on foam pad to the bottom...

Print in TPU with .4 nozzle. ... slow speed to 50% when inserted portion begins printing

You should keep dirt and debris from accumulating inside your charging port to ensure it functions properly and maintain its appearance.

Print with PETG Use Supports 100% infill

new and improved Flush Charger plug w/ pokeball finger grip Print Facing down as shown if u wanna give me money 1 time - https://rickyrickmyball5.gumroad.com/l/ifjhvi if u wanna give me money monthly - https://www.patreon.com/RickyRickMyBalls

Mini wings. Rail guards for OW Pint. ... Just use double sided foam tape to attach.

This new footpad steps in as a direct replacement for the original rear footpad, boasting a pronounced 7mm side-to-side concavity and a significant 15mm lift at its rear lip. ...Printed upright, with its front-facing edge elevated by an 8mm brim, this...

This is a newly designed component. I attempted to utilize https://www.thingiverse.com/thing:3780931 and found it performs exceptionally well but requires my nails to remove it. This new design has a similarly-tight fit, plus extra clearance on the...

Chopped and hacked at TickTock's excellent Pint Touch Fender to make room for the axle blocks and raised stock tire on the Pint. ...Then added a bit of plastic to reinforce some thin pieces and to better allow for mounting other pieces on the...

You can install this underneath flexible footpads like the Kushpad to increase traction by adding more grip. It adds approximately 0.9cm of extra height. To secure it properly, you'll need four 10-32 screws that are 1-1/4 inches long. ...Please note...

I've got a brand new Powerworks battery that's rocking a 60v and 5A rating, but I quickly realized it didn't share the same sleek design as my trusty Greenwork. So, I decided to hit the drawing board and give the Slider for Powerworks a major...

Once I added some aftermarket parts, my XR no longer fit my stand. this is a 35mm extender so you can fit in some chonky boards now. For Bolts I used 1/4"-20 machine screws with a flat philips head. ...I had to cut them down to just shy of 1" as I...

This is a remix from <a href="https://www.thingiverse.com/thing:4002135" target="_blank">this</a> original thing. It fits well. ...I also used <a href="https://www.thingiverse.com/thing:5427981" target="_blank">this</a> thing to make the hole.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/bqhVaAtcCDd

Redesigned the rESCue mount from https://www.floatboxx.com/downloads to use an alternate DC step down. https://www.aliexpress.us/item/2251832828052525.html?spm=a2g0o.order_list.order_list_main.11.7e9a18024d700l&gatewayAdapt=glo2usa Either 90V or...

A user requested a sealed battery compartment. ...Therefore, I designed and created one.

I made these mounts to carry my euboom while I ride without a backpack. I eventually will make a plate so you can use the fins at the same time but I don't have a set yet to measure the mounting holes. I used these super useful cable ties that...

I've modified this one slightly to make it fit on my Prusa MK2: https://www.thingiverse.com/thing:3784846 Original design by Patrick Denis. Trimmed 15 cm from two sides so it fits perfectly on my Prusa MK2. ...This is the 'with rails' version.