bose speaker stand 3d models

My speakers' legs are busted, so I require a stand to hold them upright. ...This is specifically designed for the Logitech Z3 Speakers.

A sleek desktop speaker stand engineered specifically for my prized Jamo speakers. ...Its clever design enables me to precisely angle the speakers directly toward my ears, creating an immersive listening experience as I sit comfortably at my...

Speaker stand for the Edifier R1280DB. There is enough room around all edges to easiy modify for different speakers. See the attached pictures for the dimensions. ...This will give the speaker a +- 13 degree angle.

simple stand for bluetooth speakers and phone. 2 pieces. i split in 2 pieces instead of one because some speakers have passive radiator on the back and with this configuration the speaker work better. you can leave your phone over the speaker...

My problem is that I had fairly good speaker stands but the attachment system for the speakers was scratch. Yamaha brand speaker stand (5.1 system kit). The scratch was a real constraint when I wanted to change my speakers. So I made this...

I built a pair of two-piece speaker stands specifically designed for my Bose Cinemate system.

Another Bose Soundlink Mini on a table stand just getting familiar with it.

I'm looking for a phone stand that also serves as a speaker for my BQ Aquarius E4.

A small stand for the bluetooth speakers I have, so that they can sit under my monitor

This is a stand for the Divoom Timebox-Evo. ...But can also be used for other smaller speakers.

Audioengine DS1M Speaker Stand - replication.This is not the exact model, only a rough model that looks the part.

Nice phone stand with passive speakers, it works but don't expect miracles. ...Made with PLA & PETG

People love having their phone stand and speakers combined into a single unit that fits easily in their hands.

A small stand that angles a small bluetooth speaker towards your face for better sound.

 Route the speaker wire through the rear hole for some measure of security (example: standing desk, in case wire gets pulled when raising desk, to avoid pulling the speaker off the stand).  Smaller part is washer which uses M2 screw and heatset nut...

A simple speaker stand to lift it off the surface and slightly angle it backwards. ...I designed this stand for my Kanto YU6 speakers to better direct the sound from the tweeters but should fit other similarly sized speakers as well.

Create a speaker base for floor-standing speakers and subwoofers to minimize vibration-induced resonance within your structure, resulting in improved audio quality. ...This also helps reduce noise disturbances for neighboring residents.

This foot is designed for a 1x1x30 (or similar) speaker stand base. To install, print four feet per speaker and affix them as near the edge as feasible. ...The bottom's slot allows for adjustments on uneven surfaces.

Basic speaker stand, angled up. Indents spaced to match the rubber feet of the speaker so it does not slide back. ...Indents in the bottom as well for small rubber feet.

The speaker stand with an iPad provides an elegant solution for enjoying music or watching content. This 3D model is compatible with the MEGABOOM 3 speaker and every version of the iPad. ...No support needed.

I designed a unique speaker stand that perfectly positions my A5 speakers at the ideal angle while sitting comfortably at my desk. ... Key Features: Width: 10cm Depth: 14cm Height: 4cm (at its highest point) Rear lip height: 1.9cm

Design of a low angle Loudspeaker stand for the AudioPRO A28 Speakers. ...As my TV and Speakers are placed on a low board, sound direction was moved a bit up to get a more direct sound perception.

The Harman Kardon Citation One Speaker Stand is designed to enhance stability and security. ...By fitting a bracket, users can create an ultra-sturdy foundation for their high-end speaker system.

This is a tilt stand for bookshelf speakers to angle them down or upwards, in my case I needed mine to angle mine downwards. My speakers are 6.5" bookshelf Dayton Audio bookshelf speakers but I am sure this would work with any bookshelf speakers. You...

Designed to sit in the center (hidden from view) of a ~12.4" x 11" (314.96mm x 279.4mm) base speaker and tilt front edge ~1.125" (28.575mm), Angle of wedge is ~6º Each Stand needs: Qty 1 Speaker Wedge Brace 1 Qty 1 Speaker Wedge Brace 2 Qty 2...

I wanted a speaker stand for my desk that would complement the Teufel ConceptC 2.1 satellite speakers, which were previously known as concept C 100. A slight up angle was necessary to enhance sound quality, so I designed a stand with this feature in...

A minimalist speaker stand that skillfully elevates your bookshelf speakers to a perfect 15-degree angle. Engineered specifically with the Micca ON3 bookshelf speakers in mind, but versatile enough to work seamlessly with almost any setup. ...Crafted in...

Unofficial speaker stand/holder for the ONEaudio micro. Holds the speaker at an angle of 30 degrees. ...Slot on top is for USB power cable and the two slots on the bottom are for adding weights to keep the speaker stationary at louder volumes.

... to print their own copy instead of modifying an existing product. The speaker fits perfectly on the stand without any additional support, but two slots are available for inserting M4 screws directly into the speaker for added stability if needed.

Rise miniBOOM speaker stand I designed in Tinkercad. I made it hollow so you can have the charging cable attached. ...I did use supports to print it.