bot chain 3d models
59873 3d models found related to bot chain.thingiverse
These are chain mounts for the Ord Bot Hadron by RepRapDiscount for use with rotoscan's cable chain. ... There is one on the nema motor that cradles the stand offs and another for the x-carriage that uses M4 bolts to mount to the existing holes.
thingiverse
Parts for adding drag chain and filament sensor to D-bot. ...Still testing files for fitment.
thingiverse
I designed these for my D-Bot build ( https://www.thingiverse.com/make:390343 ).I have been asked to put these files up for someone who wants to use them, but as to whether they will be of any use to anyone else, who knows.
thingiverse
This is a customized open cable chain based on Claghorn's design here: https://www.thingiverse.com/thing:611593 Increased cable chain size 20% to allow more wires to fit inside. I run a Titan Aero and have a CiiCooler and BLTouch on my extruder...
thingiverse
This chain component, coupled with my Gear for Bots, makes a good gear & chain combination for any time you want to convert linear motion into circular motion or vice versa. Instructions print...
thingiverse
Credits to the D-Bot community : http://www.thingiverse.com/thing:1001065/#remixes
thingiverse
This is a frame mount and a carriage plate mount for a large cable chain to be mounted on my D-bot. The chain is http://www.thingiverse.com/thing:951006 which I printed at 60% scaling, which is still quite large. The carriage plate mount mounts onto...
thingiverse
A rigid cable chain was a better solution, however the existing ones used with the D-bot were both too small for the number of wires necessary for a dual-extruder hot-end with a BLTouch, but they required feeding all the wires through the chain at...
prusaprinters
The weight of the wiring going to the hot-end on my D-Bot derived printer was high enough that none of the normal ways of supporting them (3mm filament, PTFE tubing, etc) would support them well enough to not sag, occasionally getting in the way of...
thingiverse
A 15x25 chain cable beetween "Rear_Idler_Right" and "Print_Carriage_Rear",
thingiverse
This is a mount for the top of this carriage. ... This was meant to be used with most 20mm cable chains and as an opposite point for this tower
thingiverse
Some of the parts I used in my C/D-bot build if anyone else finds them useful. ... To be used with 20mm cable chain (http://www.thingiverse.com/thing:668048) .
cults3d
Some of the parts I used in my C/D-bot build if anyone else finds them useful. ... To be used with 20mm cable chain (http://www.thingiverse.com/thing:668048) .
thingiverse
The X-Axis chain with open links. ...Easy to place wires. The Z-axis chain will be added to the motor idler. But design in progress. Stay tuned and check for updates! ... Designed for this monster : https://www.thingiverse.com/thing:2478329
cults3d
End mount cable channel 7x15 mm for 3D printer "Good Bot" by kerbetos installation materials::cable chain 7x15 mmM3 screwinjection nut (M3, thin)
thingiverse
End mount cable channel 7x15 mm for 3D printer "Good Bot" by kerbetos installation materials:: [cable chain 7x15 mm](https://www.aliexpress.com/item/32969673063.html) [M3 screw](https://www.aliexpress.com/item/4000970993800.html) [injection nut (M3,...
thingiverse
] This is a set of additional parts for [Phaedrux](https://www.thingiverse.com/Phaedrux)'s modified carriage: * A flipped tension block for use on the back of the carriage, if you want to put a half-twist in the belts * A shortened Dii cooler...
grabcad
Rendering of a scale of a human model bot.check the first version done by Jarde Dummy here Jarde Dummy
thingiverse
There will also be add-ons to the bots like hats that can be printed extra. So far I have gotten 3 done and am starting to work on the first extra hat. These bots can be printed without supports but supports are recommended. You will then need pliers...
sketchfab
This is a model of a AI driven bot which collects organic waste and recycles them. ...The functionality was inspired by the game pacman and the shape and aesthetics were inspired from a farmer’s wholesale market in India.
grabcad
this was a project I did for a competition in which the task was to push some balls into holes to clear the path of the bot to reach the finish line
thingiverse
... mount and the filament mount are wrapped around the frame using M3 screws and bolts. (I ran out of t-nuts). C-bot:http://www.thingiverse.com/thing:500041http://www.openbuilds.com/threads/c-bot.726/ D-bot:http://www.thingiverse.com/thing:1001065
prusaprinters
The working range is 160 mm diameter x 200 mm long. The electronics used to control motors and Engraver is Eggbot original. The design is printed, visible in the photos, is Eggbot Op Art dnewman; Thing: 7099. Thanks to Dan Video:...