bow and arrow nock 3d models
2234564 3d models found related to bow and arrow nock.thingiverse
Custom Section o Objectives: To 3D print, attach, and then fire an arrow with the 3D printed model acting as the arrow fletching and nock. o Audiences: Any age that can understand 3D modeling and archery safety precautions. Our specific audience is...
cults3d
... teacher asked if it was possible to 3D model a replacement. After repeated renditions (approximately 25), they were able to the exact fit for the arrow shaft with everything the correct size. ... The arrows fire perfectly, unless you hit a tree.
thingiverse
This is a nock for carbon arrows with a diameter of 5.6mm. ... I tested it with a 26lbs Bow (30lbs on the hand) and it works perfectly. ...
thingiverse
I have bow and arrows, but they're quite old, and one problem is that the nocks keep breaking off (the nock is the part that clips onto the bowstring, I didn't know that until I googled it). I decided to design a piece that could fit over the broken...
pinshape
WARNING use at your risk this is untested and NOT guaranteed to be safe especially with stroger bows. This is an arrow nock for dowel arrows. Do NOT use a taper tool. I made this for a pencil sharpener, sharpen until the dowel fits. ...Print at 100%...
cults3d
Sometimes on our archery practice the nocks jump from the arrow when hitting the target. I usually can't seem to find them nowhere, so i decided to design my on nocks to print them when i lose one. From the safety point It's always better to buy...
thingiverse
... the arrow and glued in. I used rubber cement in case I needed to pull it out to replace it. They turned out to work really well. I used this on arrows from the Bear Archery Scout Bow Set and a few others we purchased. ... I printed with a brim.
myminifactory
I have bow and arrows, but they're quite old, and one problem is that the nocks keep breaking off (the nock is the part that clips onto the bowstring, I didn't know that until I googled it). I decided to design a piece that could fit over the broken...
thingiverse
Sometimes on our archery practice the nocks jump from the arrow when hitting the target. I usually can't seem to find them nowhere, so i decided to design my on nocks to print them when i lose one. From the safety point It's always better to buy...
thingiverse
I've printed it at a 0.1mm layers and dropped speed to 10mm/s with 35% fill will test it on a low powered bow 1st and then maybe my 20# recurve. ...More Archery posts in my group http://www.thingiverse.com/groups/3d-toys If you want to see more and how...
thingiverse
This is an archery arrow nock. ...It fits my Easton XX75 1916 arrow shafts with a little post production.
cults3d
hi the file is arrow nock for arrow bought from taobao,only 20 rmb 3 arrows,much cheaper than Nerf Sports Dude Perfect Arrow Refill package,details can see my mod video on youtube~
thingiverse
hi the file is arrow nock for arrow bought from taobao,only 20 rmb 3 arrows,much cheaper than Nerf Sports Dude Perfect Arrow Refill package,details can see my mod video on youtube~
thingiverse
Arrow nock i made from scratch hope you like it plz comment below on what i could improve on it
prusaprinters
A simple tool to align and insert the nock in the arrow shaft. ...So far the tool was only tested with Easton nocks but should work for most.I recommend printing it with 100% infill
thingiverse
A base for an arrow with nock and feathers, use a 6mm (wooden) stick to mount on. ... Printed in TPU, good results with supports printed upside down.
thingiverse
After breaking the nock (the piece that keeps an arrow on the bowstring) on a steel arrow I had, I designed this. I'm not an expert on archery, so you may need to do a bit of scaling to get just the right fit. ...If you want the part to keep up with...
thingiverse
This is an arrow nock for 5.5mm shafts. Added another stl for 8mm shaft. ... Instructions This may be stronger printed on it's side with support.
thingiverse
Arrow Nock 4.2mm. To scale, use the DWG file. I have not tested it yet. ...Let me know if it works
thingiverse
This is a great little part which will save you a fortune when buying new nocks for your arrows. They work really well when made from Carbon Fibre Filament, use 2 shells and 100% infill to make it durable. 3Dynamic Systems Carbon Fibre Filament...
thingiverse
remove all remaining glue attached for me, it worked out fine at a 101%, without any need for glueing Even I know there already are a lot of other nocks around, ....in my case (schaft a little scattered at the end) this works better for me, maybe...