bowden cable fittings 3d models
464288 3d models found related to bowden cable fittings.thingiverse
... ...Useable for Rostock printers with 6mm bowden and 10mm Push-Fits. Instructions Inner diameter of bowden Push-Fit hole: 10mm (+tolerance). Inner diameter of filament hole: 3mm (+tolerance). Screw holes: 4M. ...Distance of the two screw holes 50mm.
thingiverse
A pair of replacements clamps to retain your Techzone Huxley bowden cable using 6-R1/8 straight push-fit pneumatic fast connectors. All my attempts to retain my ptfe bowden cable before that turned into a failure sooner or later. Now that I use...
thingiverse
Customized version of http://www.thingiverse.com/thing:17234 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=17234 Instructions Using the following options: tube_dia...
thingiverse
With only 10cm - 20cm bowden. ... To pull in a gently radius and not over a sharp edge!
thingiverse
With only 10cm - 20cm bowden. ... To pull in a gently radius and not over a sharp edge!
thingiverse
Just a simple coupler for the M6 Bowden style fitting. ... 100% infill with supports
thingiverse
Just a simple coupler for the M6 Bowden style fitting. ... 100% infill with supports
prusaprinters
Just a simple coupler for the M6 Bowden style fitting.100% infill with supportsPrint SettingsPrinter:Creality CR-6 seRafts: NoSupports:YesInfill: 100Filament:Matterhacker PLA blue Notes: Category: 3D Printer Accessories
cults3d
(You will need to calibrate extruder steps-per-mm after the change) ####And one post-processing step: * Clean the filament path with a drill (5/64" or around 1.9mm) Changes made in the remix ####mount piece * Pre-drilled for an M4 pneumatic fitting...
thingiverse
(You will need to calibrate extruder steps-per-mm after the change) ####And one post-processing step: * Clean the filament path with a drill (5/64" or around 1.9mm) ### Changes made in the remix ####mount piece * Pre-drilled for an M4 pneumatic...
thingiverse
This design was aimed at long bowden run and uses 3mm multi-core stainless steel cable to add a rigid yet flexible support to the filament line. ...Also added room for a m10 pneumatic fitting and 2x 5mm grub screws to retain one end of the cable.
thingiverse
I use this thing to attach bowden cables to plastic-mesh. ...The 4 holes are for cable ties - that makes it easier to point the bowden cable in the right direction.
prusaprinters
I use this thing to attach bowden cables to plastic-mesh. ...The 4 holes are for cable ties - that makes it easier to point the bowden cable in the right direction. Category: Robotics
thingiverse
This is a replacement Bowden Cable Clip for the Bike Bergamont Sponsor Tour He.28" Thanks, Enjoy! ...
thingiverse
Simple clip to connect bowden tube and hotend cable / Einfacher Clip um Bowdenrohr und Hotend Kabel zu verbinden
thingiverse
I modified Erik's Bowden Cable Coupling to fit the bolt spacing on the Mendel X carriage and extruder body. I use the closer spaced holes to mount my custom hot ends. Instructions The STL file is a...
thingiverse
... ... I've also a camera USB cable and I need a 3-cable clip. The normal clip is also more longer, more stronger and resistant. There are 3 clip: Bowden + cables (like the da-syggy one, but with clip 2mm longer. Bowden + cables + USB Cables + USB
thingiverse
Instructions Minimal instructions if you have a stock printrbot print a extruder-to-bodwen and a bowden-to-hotend Install the Pneufit adapters on your bowden cable and screw it onto the 2 printed pieces install this on your printer Extended...
thingiverse
I'm thinking to use this eventually for printing polycarbonate with my hotend - just hook up the bowden cable to some similarly sized PEEK-based tubing and feed the PEEK to the hotend. Updates: 7/30/14: removed overhang in the center portion. ...This...
thingiverse
This is a cable and tube guide for a Bowden extruder. 4mm tube Radius for the cable guide is 8mm. The opening for the cable ties is for 2.5x1mm cable ties. ...Print Settings Printer: UM build ...
thingiverse
These cable clips allow you to attach cables to a 4 mm PTFE Bowden tube, like for example the hotend supply cables on an Ender 3. Never waste zip ties again! Choose a cool color and print four or five of them, then simply clip on your cables. This...
thingiverse
A Mendel bowden cable interface for use with a bowden extruder such as http://www.thingiverse.com/thing:1947 Update: Design is being reworked - had some issues when I printed - will post a working version once I have one :) Instructions Print each of...
thingiverse
I was tired of zip-tying my bowden tube to the hotend cable wrap and cutting them off every time I needed to change something, so I chopped these clips off of ZoltanKi's clip/mount. ... I printed it light with 2 wall lines and 10% infill, and they...
thingiverse
Just a simple clip to connect the bowden tube to the cables for the hotend and keep them nice and tidy Print Settings Printer Brand: RepRap Printer: Prusa Mendel i3 Rafts: No Supports: No Resolution: .2 Infill: 100% Notes: Nothing special about the...
thingiverse
Sometimes my 3mm Plastiks gets stuck in the bowden cable because it has 3,10mm or isn't perfectly round. Since the inner diameter from the cable is 3mm there is no margin. One plastic got so stuck that it was impossible to remove so i had to cut the...
thingiverse
Various clips for tying cables together for 3d printer hotend.
thingiverse
I quickly realized that the ones on my UM2 would not work on my current build because I am using a smaller bowden tube. So I came up with this one! Works quite well on my printer! Let me know what you think! ...Print Settings Printer Brand: ...
thingiverse
... made my own and it worked best for me. ...Printed from ABS on 0.1 and 0.15 layer heights, often use it as 'mickey ears' around the model. I'm used to cut bowden rings from each other with a knife but they can be torn apart with hand on a good print.
prusaprinters
I quickly realized that the ones on my UM2 would not work on my current build because I am using a smaller bowden tube. So I came up with this one! ...Works quite well on my printer!</p> <p>Let me know what you think!</p> <h3>Print Settings</h3>...
thingiverse
... have other uses. I created this for a trunk lock cable on my car, I didn't have any single piece of housing long enough on hand. Should print OK without support. ...Use zip ties through the rectangular holes to hold ends ouf housing in place.