bowflex pr 10000 3d models
3939 3d models found related to bowflex pr 10000.thingiverse
... Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=518217 Instructions Using the following options: raised = 0 box_width = 50 box_wall_thickness = 3 box_high = 40 message = Pr font_size = 20 box_depth = 40 Font = write/orbitron.dxf
thingiverse
I was gifted a broken set of bowflex selecttech 552 dumbells and I couldn't find any other designs that would actually work. The other two versions of these disks on Thingiverse caused excessive resistance when trying to adjust the weights. I...
thingiverse
Customized version of http://www.thingiverse.com/thing:169491 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=169491
cults3d
Knife kit, choose your blade, guard, pommel and handle to make your own, 10000 different possibilities ! The blades are meant to be printed with flexible filament (if you print with rigid filament you with need to sand the tang a bit of scale a few...
thingiverse
Knife kit, choose your blade, guard, pommel and handle to make your own, 10000 different possibilities ! The blades are meant to be printed with flexible filament (if you print with rigid filament you with need to sand the tang a bit of scale a few...
thingiverse
For those that like me, hit rarely and few times the screws while moving around the Bowflex, the covers to minimize the hit.
thingiverse
My Bowflex 2080 Barbell weights stick sometimes. With this spacer in place, it changes the angle just enough to prevent sticking. ...Depending on your setup, you may need to change the thickness.
thingiverse
BowFlex 552 FIrst Generation 5-52.5lb dumbbells (red numbers on dial). These discs were made from photos of the discs. ...They are labeled properly on files but i neglected to properly label them inside the SW files
thingiverse
This is reverse engineered from a Bowflex SelectTech Dumbell. The Disk is the one labelled "3". ...I printed this disk in ABS and it has been working well for about a year now.
thingiverse
If you're like me and frustrated with your phone obscuring the Bowflex Max display try this. The mount simply clips into place and is then very sturdy. Works with phones up to 94mm wide. Has hole for charger cable—need to print with supports here...
thingiverse
I designed this spacer to work in conjunction with a Bowflex Power Rod Rejuvenator. ... The spacer holds the middle of the power rods in place while the Rejuvenator clamps them at the free end, yielding much better straightening than with the...
thingiverse
I designed this to hold my tablet while working out on the Bowflex Promax trainer. I cant take credit for the idea, but I did design this from the ground up with Fusion 360. You will need to screw the two separately printed pieces togegether. Since...
thingiverse
Customized version of https://www.thingiverse.com/thing:2936919 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2936919
thingiverse
Customized version of https://www.thingiverse.com/thing:1148986 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1148986
thingiverse
Customized version of https://www.thingiverse.com/thing:612709 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=612709
thingiverse
Customized version of https://www.thingiverse.com/thing:2482372 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2482372