bowflex selecttech 552 series 1 replacement part disk 3 3d models

One of the adjustment knobs on my Atten AT5010B broke, so I made a replacement. I used 100% infill just to be sure, since installing this was time-consuming. You can see it installed in the lower part of the picture. ...(the gray pin) Let me know if...

I ordered a new replacement part for my Cozyna Manual-Grinder after it suddenly snapped in two just a few months into regular use. ...Fortunately, I was able to find an exact match on Amazon that fits perfectly, which you can see here:...

... to install with PLA. Ersatzteil: This is a holder for the soap dish in a Hansa shower set. This design is thinner than the original and clips on easily. Original price for the part with soap dish (only available as a set): approximately 17 euros

This is a replacement part fo the Commercial Electric branded light bulb changer part that connects the light bulb holder to the rod. The fit is very snug for the 8 metal flaps, so expect to use some force to insert them in. ...The non standard...

... ...Unfortunately, a wall suddenly appeared in front of me and destroyed the front part. Now that I have a 3D printer, I decided to create a replacement part myself. And here it is! ...Hopefully, this can help others who may be in a similar situation.

Replacement component for miniature Heki roof lamp.

A Gotek USB Floppy Emulator Caddy that fits systems that have an internal 3 inch disk drive such as the ZX Spectrum +3 and Amstrad CPC6128, 664 & the external drive enclosure FD-1.The front plate has holes for the standard gotek board (green led,...

This is a custom replacement part designed for the Vtech VM-343 baby monitor parent unit. The original antenna was damaged by my son, prompting me to create this replacement. Unfortunately, Vtech no longer manufactures parts for this model. To...

Replacement Part for Nose Gear of Apprentice S15e. I deliberately chose not to purchase a complete nose gear replacement kit since I only required the arm; instead, I designed one myself. Both parts can be joined together using glue, but this is...

In this final part of our practice flume series, we'll delve deeper into the mechanics and applications of flumes in hydraulic engineering. ...With the knowledge gained from parts one and two, you'll be equipped to tackle real-world scenarios and master...

This is a replacement part for the Citroën Saxo model center console. Its a direct fit, super easy and straightforward installation.  Uses the same installation mechanism as the original part. ...And the gray one is the exact same one but sanded a bit...

Uncovering the World of Feline Companions: A Journey into Cat Part 3

Excavator 390F Part 3 https://www.youtube.com/watch?v=u3hJfZg5xvk

Designed to replace the original dividers for Allsop 5 1/4" floppy disk, storage boxes.

If plastic debris is obstructing the hole, use a screwdriver or similar tool to remove it before installing the replacement part. The height of the foot assembly (excluding the insert) measures 6mm. Since Ikea chair feet are notorious for their...

Within the past ten years, I've had to change the wires twice already, now the guides also need replacement as they were wearing down the new wires. This seems like bad design, however you can now easily print out a replacement. ...It is possible that...

I spent a whole night trying to find a replacement part to buy or print, but no luck. So, my troubles are for your benefit!Make sure to enable supports for at least the "top" fan opening where it connects to the blower. ...Uploaded 3mf with supports in...

This part replaces the locking mechanism of Joycon Controllers for Nintendo Switch. I tested only the left one myself, but the right one reportedly fits too. My Switch took a tumble onto the floor and detached my left Joycon. After that, it wouldn't...

summary I made this replacement part for the Hauck travel cot because the original part broke apart. From what I understand, this part seems to break very often on these beds if you are not careful in folding or unfolding the bed. There are 2 almost...

To ensure optimal fitment, carefully examine the SCAD file and make any necessary adjustments to the axle and mounting shaft dimensions before printing the replacement parts. ...Once complete, swap out the old wheels and shaft with the freshly printed...

Replacement part for teak deck chair. Printed by Shapeways.com in bronze-filled stainless steel. ATTENTION This work is licensed under the Creative Commons - Attribution - Non-Commercial license. This license only applies to files and documents...

A coworker's tape dispenser had stopped working, so I designed and created a replacement part for him. This custom component is specifically tailored for packaging tape and features a removable axle that allows it to be easily adapted to various...

... rubber base got loose and made the stand virtually unusable. ...When it happened to mine as well I decided to create this replacement part. ...Due to it being not rubbery, glueing it back in place is much easier and does the job perfectly fine IMHO.

... cheap bicycle kickstands. ...Print with the same orientation and only have support on the build plate. I added a modifier to print 100% infill on the leg part Print Settings Rafts: Doesn't Matter Supports: Yes Infill: 40 Category: Sport & Outdoors

Replacement Part for car CD phone holder that shattered due to excessive phone insertions and removals from the broken holder. You may also print this using PLA instead of ABS, but my experience shows that it loses its shape on extremely hot days.

... shroud, using the original screws. ...It's for when one (or both) of the metal flaps are broken off due to metal fatigue and you don't want to replace the entire fan shroud.It can be used any Ultimaker 2 model since they all have the same fan shroud

... you can use this design, too. You also need three metal pieces, cut out of 3,3mm screws or nails. You need one piece 14mm long and 2 pieces 18mm long. And, like most of my designs, if it does not fit your specific use, tinker with it! ... :-)

... this design as well. You'll also need three metal pieces, cut from 3.3mm screws or nails. One piece should be 14mm long and two others 18mm long. ... As with most of my designs, if it doesn't fit your specific use, feel free to tinker with it!

That model seems to be used quite often so maybe you can use this design, too.You also need three metal pieces, cut out of 3,3mm screws or nails. You need one piece 14mm long and 2 pieces 18mm long.And, like most of my designs, if it does not fit...

I created a custom drop-in replacement part to block out most of the light, and I'm excited to share it with others. I've found White PLA to be an excellent material for printing this part. Printing at 100% with supports for the small hinge...