box feet 3d models
219766 3d models found related to box feet.thingiverse
I looked everywhere for something like this but found nothing so I remixed Finger Cat Paw by alice3021 and turned it into an ornamental set of box feet along with a matching corner protector.
thingiverse
Universal box feet designet to be mounted with M3-M5 screw. ... Visit my blog for more projects:<a href="http://www.maj.pavlin.si/">http://www.maj.pavlin.si/</a>
prusaprinters
Universal box feet designet to be mounted with M3-M5 screw. Visit my blog for more projects:http://www.maj.pavlin.si/ Category: Household
prusaprinters
If you need some feet for your shelf, search no longer. 15mm tall riser / feet for any possible box / shelf / dresser / drawer. You need 2pcs. of M5x20mm or longer truss-head srews.</p> <p>You´re welcome...</p> <h3>Print instructions</h3><p>Print in...
thingiverse
... it to your needs. It is a bit too big for the feet of the control box so they do not stay if you lift the box, but that's good enough for me. ...I will update the file to fit well when I have time and have upgraded what I wanted on my printer.
thingiverse
These feet will prop up your control box 20mm, allowing the fan to breathe better. Saw the opportunity to add a slot for a SD card extension ribbon cable. If you don't to go that route, then just print 2 or 3 of the normal ones. Use 3x10mm and...
thingiverse
Customized version of https://www.thingiverse.com/thing:3178167 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3178167
thingiverse
Customized version of https://www.thingiverse.com/thing:3178167 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3178167
prusaprinters
I designed these feet and "feet receivers" to be installed on the boxes so they would stack securely. You'll find the files for the feet, receivers for the top of your box, and an installation jig so they're all installed with correct spacing....
thingiverse
Custom 2.5cm feet for the Creality CR-10 Control Box. I found the stock "feet" completely insufficient, as there's little to no room left for PSU fan intake, especially if placed on a soft surface. 4 M3 holes need to be drilled in the existing metal...
thingiverse
These are simple feet to snap on the 4 corner nuts on the Monoprice Maker Select control box to help with vibrations and noise on the glass table i have it on.
thingiverse
couple of feet to lift the controller box off the platform a little bit. the cr-10 has a fan underneath with very little breathing space, this will keep it stable and give it some room to breath for longer runs. ...
thingiverse
Here are some simple feet I designed for my CR-10 V2. They use the existing screw holes of the bottom cover. I made these as they are quick to print and use less material than the others I found. I reused the existing rubber pads. Requires longer...
cults3d
I designed these because the cost of buying in commercial equipment feet is not really justified, then you can never find the size that you want! There is a selection of different sizes and shapes here that can also be scaled in the slicer. As...
thingiverse
It's relatively thin, so to stabilize itself, it comes with two small plastic feet that attach to the bottom. Unfortunately, these feet are so weak that they break if you so much as look at them the wrong way. Even worse, Holmes does not sell...
thingiverse
I redid the design to remove the feet and make the walls a bit thicker.
thingiverse
Replacement feet for galaxy box fan. ...Will slot into original feet slots.
thingiverse
These are wide fan feet for a Lasko box fan. They may fit other models. They've also got round inserts on the underside. They're for fitting pillars to hold the fan off the floor in the event of water ingress; I just haven't gotten around to...
prusaprinters
These are wide fan feet for a Lasko box fan. They may fit other models.</p> <p>They've also got round inserts on the underside. They're for fitting pillars to hold the fan off the floor in the event of water ingress; I just haven't gotten around to...
thingiverse
So I need some new feet for my box fans... who doesn't... those things break so easy it's criminal. In any case I looked on Thingiverse and there are several available but they all need lots of support. If I'm going to use extra filament, I want it...
thingiverse
Customized version of http://www.thingiverse.com/thing:1264391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: Vent...
prusaprinters
I wanted to extend the “additional feet” and chimney for the printer-box spool tank to allow more room between the Spool Tank and MMU. ...The filament has a smooth run between the Tank and MMU.The original model can be found on the printer-box...
thingiverse
After several years the original black rubber feet of my WMF bread box are gone. The got try, hardened and brittle. As a result year sheered off when moving the box around for cleaning. Since the box is high quality, stainless steel and such a...
thingiverse
I designed the feet so you can replace the short stock ones and make the necessary clearance for the box. Using these parts allows you to move the box under the frame and have it flush to the feet and 2020 extrusions. It makes the sd card slot much...
thingiverse
... be added to the slicing software and positioned inside of the back edges. I also wanted to use the M5 T-nuts that I had on hand so I made mounting feet. One for top and one for the bottom. ...M4 T-nuts would work just fine as well with these parts.
thingiverse
This is a drop in replacement for the Sienci Longmill's controller box footers to enable it to be mounted to a flat surface. ...I used it to mount my CNC's controller box to the side of the table and out of the way.
thingiverse
The Ikea box feet stand out 1 mm so that small adhesive felt plates can stick on there. ... There is a left and a right side, you can also print only the left or right side and then turn the print part can be installed (I hope I have made myself clear,...
prusaprinters
I like the holder, I like the stability feet, I just used the same concept to add a box to hold some tools. ...A very small box, but big enough to hold tweezers, steel brush, sceaning sponge and even some nozzles.Print instructions-Gyroid Infill 15%.-2...