box lid designs 3d models
999701 3d models found related to box lid designs.pinshape
Lids so far: Blank Lid for adding your own design. Orion Constellation Maiden, Matron, Crone symbol (2 crescent moons, full moon between) Saturn Earth Cat-Hat-Broom - Whiskers didn't print well for mine, may have made them too small. I'm...
thingiverse
This is a parametric box with a snap-fit lid in FreeCAD using the part design methodology. It's a nice thing to have if you're designing custom project boxes etc, as it gets the tedium of the box out of the way so you can concentrate on pockets etc...
thingiverse
... ports open for easy access. Different lid designs are available depending on your needs. Leave any feedback below and be sure to to upload pictures of your prints! ... Edit: Added a thicker lid piece that seems to seat better than the original.
thingiverse
jewelry box has a perfectly fitting lid. Featured with bevelled edges and designpattern in lid & bottom plate to prevent warping and pulling off the bed. Print without support, infill between 10 and 100 % works fine. ... ...
thingiverse
Simple box and lid design. Make sure the top of the box is facing up. ... 0.30mm 20% infill
thingiverse
I broke the lid to my Planetay Designs Airscape container and needed a new one.
thingiverse
(48 x 86 x 4) mm -- (W x L x H ) Internal Squares 32 mm 36 mm This design is a miniature designs box. ...It can be used as a container with the cage design, available in my profile, or as an exhibition holder.
prusaprinters
This is a remix of the electronics box lid designed by 'the freewheeler'.I love the Apple Mac Pro “Cheesegrater” lattice and thought the electronics box cover would be a perfect place for this.Printed this lid in PLA, Silk and PETG with 0.1mm layer...
thingiverse
this is a parametric box with snap on lid. it is scaleable and has 4 mounts that you can position in z height and x,y location for a circuit board to bolt in on. it has rounded corners, ability to print just the cover or the box, and the ability to...
cults3d
4 types of boxes 2 length https://www.youtube.com/shorts/Zb-p63GQdpo
thingiverse
Lid for box. Better ptint with flex type of filament or half flex. ...But PETG work well to.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1561008 Instructions Using the following options: box_label_width = 5 box_separators_over_width = no box = no rings = yes lock_system = yes box_height = 50 box_separator_number_length = 3...
thingiverse
Using a caliper I measured the dimensions of a box and its lid This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/1sbe7b0JjJr
thingiverse
Very simple, still learning Fusion360, but the lid fits well but not tightly. Easily resized. ... I printed at 25% infill, would have been over 20 hours at 100%.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=189264 Instructions Using the following options: boxLength = 40 cornerRadius = 5 lidThickness = 3 boxHeight = 25 lidEdgeThickness = 0.5 itemsShown = lid bottomThickness = 3 textThickness = 2...
thingiverse
L=6cm x W=6cm x H=4cm Walls and lid 4mm thick. Note: Raft and support structures were not required in my case but you may find a raft useful if you have a problem with large flat objects sticking to the platter. Also some supports may be used in...
thingiverse
Stackable box, for bolts, nuts, or other stuff. ...3 different designs
pinshape
SummaryStackable box, for bolts, nuts, or other stuff. ...3 different designs